AuthorTopic: will these fit..........  (Read 1396 times)

0 Members and 1 Guest are viewing this topic.

Offline spinkster

  • Posts: 76
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Its only kinky the first time

spinks

1988 110csw 200tdi retro fitted

Offline martha focker

  • Posts: 593
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
will these fit..........
« Reply #1 on: September 20, 2007, 10:40:07 »
i would say so but see what the rest say first :D
don't worry i'm here

www.gotmud.co.uk

www.rib.net

Offline Xtremeteam

  • Regional Rep
  • *
  • Posts: 6476
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Its just the way i roll
    • lampeter, west wales
  • Referrals: 0
will these fit..........
« Reply #2 on: September 20, 2007, 11:27:39 »
aslong as they come with the caliper mounting brackets

you may need different 1/2 shafts but in not 100% sure
Mike
I can Drive.. You can criticize..
I too can criticize like you.. but can you Drive like me??


Offline L90OOK

  • Posts: 1252
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
    • Somerset
  • Referrals: 0
will these fit..........
« Reply #3 on: September 20, 2007, 13:05:05 »
You may have to get different stub axles as there are a few variants.
if they are the earlier type you should be ok.
May also have to change drive shaft but they are cheap enough.
Did everyone see that?  Because I will NOT be doing it again!

 

Guardian.

  • Guest
will these fit..........
« Reply #4 on: September 20, 2007, 13:24:33 »
could just change the whole axle for disc type, they dont make much more than that usually on ebay.

Offline muck_truck

  • Posts: 124
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
will these fit..........
« Reply #5 on: September 20, 2007, 16:23:48 »
most ptobably wont fit as yor axle tube wont have the calliper mounts.

i bought a disco rear axle and was going to keep my 90 axle tube but the mounts for the calliper are cast on the axle tube.

Wont you have a sailsbury rear axle ?  wouldnt the hubs be different to rover ones
Dan.

Defender 90 200Tdi
www.muckytruckin.co.uk

Offline iomlr

  • Posts: 216
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
will these fit..........
« Reply #6 on: September 20, 2007, 16:48:23 »
Quote from: "muck_truck"
most ptobably wont fit as yor axle tube wont have the calliper mounts.

i bought a disco rear axle and was going to keep my 90 axle tube but the mounts for the calliper are cast on the axle tube.

Wont you have a sailsbury rear axle ?  wouldnt the hubs be different to rover ones


correct wont fit! need a rrc or a disco or a landrover rear axel that has had discs before!
Bobtail Range Rover 300tdi Manual
Body lifted, Gywn Lewis Challenge Suspension. Mach 5's with Jungle trekker Tyres ARB Locking Diffs Front and Rear. Steering Guard and Axel / Track Rod Guard. Modified bumpers front and rear Custome Rock sliders. Roccia Comp Arches,  Eleci Fans with X switch.

V8 90 County Defender. Rebuilt with galvanised chassi and bulkhead, Tubular sports manifodls and sports pipe. Old Man Emu suspension, under axel guard. BFGoodrich Muds on Mods.

Offline spinkster

  • Posts: 76
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
will these fit..........
« Reply #7 on: September 20, 2007, 18:15:39 »
ah i wont bother bidding then.........i was just browsing and they looked cheap enough if they'd fit..................so what exactly do i need to change my salisbury to disc braked?
Its only kinky the first time

spinks

1988 110csw 200tdi retro fitted

Offline Xtremeteam

  • Regional Rep
  • *
  • Posts: 6476
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Its just the way i roll
    • lampeter, west wales
  • Referrals: 0
will these fit..........
« Reply #8 on: September 20, 2007, 20:05:42 »
Quote from: "iomlr"
Quote from: "muck_truck"
most ptobably wont fit as yor axle tube wont have the calliper mounts.

i bought a disco rear axle and was going to keep my 90 axle tube but the mounts for the calliper are cast on the axle tube.

Wont you have a sailsbury rear axle ?  wouldnt the hubs be different to rover ones


correct wont fit! need a rrc or a disco or a landrover rear axel that has had discs before!


incorrect

the caliper mounts bolt onto the mounting ring that the stub axle bolts onto

BTDT converted my dads truck to discs
Mike
I can Drive.. You can criticize..
I too can criticize like you.. but can you Drive like me??


Offline muck_truck

  • Posts: 124
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
will these fit..........
« Reply #9 on: September 21, 2007, 11:13:31 »
Quote from: "Xtremeteam"


incorrect

the caliper mounts bolt onto the mounting ring that the stub axle bolts onto

BTDT converted my dads truck to discs


are you talking about sailsbury or rover axle?  cause im prety sure that the the caliper mounts where part of the tube cast on the disco (rover) axle i bought.

Sailbury has a bolt on mount for a caliper.
Dan.

Defender 90 200Tdi
www.muckytruckin.co.uk

Offline Xtremeteam

  • Regional Rep
  • *
  • Posts: 6476
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Its just the way i roll
    • lampeter, west wales
  • Referrals: 0
will these fit..........
« Reply #10 on: September 21, 2007, 13:58:53 »
your talking about a standard axle,
im talking about a salsbury which will be fitted to his 110,

on a 110 its all bolt on bits
Mike
I can Drive.. You can criticize..
I too can criticize like you.. but can you Drive like me??


 






SimplePortal 2.3.5 © 2008-2012, SimplePortal