AuthorTopic: Sealants and stuff  (Read 1667 times)

0 Members and 1 Guest are viewing this topic.

Offline Welshbreed

  • Posts: 360
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Motorsport Service & Repair Level 3 Technician
    • @MrSmeeZus
  • Referrals: 0
Sealants and stuff
« on: June 05, 2007, 23:59:29 »
whats are the sealants used between all the metal parts?

ie:
1/ between the seatbox and tub
2/floor panels and sill channels / seat box / transmission tunnel
3/ nuts and bolts / aluminium etc
etc, etc

also what washers should I use to stop the heads of bolts and nuts etc, effecting the birma in the long term?

anyhelp appreciated
thanks in advance, alex





Offline mark.yellow.series.3

  • Posts: 1357
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Sealants and stuff
« Reply #1 on: June 06, 2007, 22:31:39 »
for sealing the joints i use polyurithane, use like silicon, but very strong.

Offline The Landy Guy

  • Posts: 262
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Sealants and stuff
« Reply #2 on: June 06, 2007, 23:07:19 »
where can you buy that?
Series Rule!!!!

1970 Series 2A SWB(89-inch) Truck Cab

Offline Welshbreed

  • Posts: 360
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Motorsport Service & Repair Level 3 Technician
    • @MrSmeeZus
  • Referrals: 0
Sealants and stuff
« Reply #3 on: June 07, 2007, 00:17:53 »
Ok polyurithane, brilliant... screw fix have any?





Offline mark.yellow.series.3

  • Posts: 1357
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Sealants and stuff
« Reply #4 on: June 07, 2007, 19:24:51 »
i would think screw fix should have some. if not a descent hard ware shop will sell it.

screwy

  • Guest
Sealants and stuff
« Reply #5 on: June 07, 2007, 19:58:43 »
The proper stuff to use is called DumDum. It is a black non-setting sealant a bit like thick putty. It is also used to seal in the windows. Youn can get it from Paddocks.

Personally I don't like DumDum and I detest silicone or similar on joint that you may reasonably be required to take off in the future, such as gearbox/transmission tunnel, floor plates, etc, if for nothing other than access.

I have used a foam rubber sealing strip which is self-adhesive on one side. Press all around one panel and then bolt  up. The foam rubber is compressed between the joints forming a weather tight seal. But the beauty of it is, if you need to take that component off, it will come of and the foam strip can be scraped off easily, so less mess and hassle. It has an added benifit of better sound insulation I have found. This type of sealing is frequently used in ductwork and ariconditioning units, etc.

I think Screwfix have started stocking it too now. I kinda get mine for free at work..... :wink:

Offline Bob Ajob

  • Posts: 255
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Sealants and stuff
« Reply #6 on: June 08, 2007, 17:42:10 »
If you're after non-setting waterproof putty, I've come across Plumbers Mait before now from B&Q, or any hardware store. It's a non-setting putty that plumbers use, worth a try perhap? Comes in 1.5kg or 750g, and not expensive either.
Amber is a 1971 Series IIa with a 2286 petrol


screwy

  • Guest
Sealants and stuff
« Reply #7 on: June 09, 2007, 15:19:41 »
Plumbers mait would not be of use in the applications described I am afraid. It is primarily a jointing seal for threaded pipework. Used between floor plates for example, it wouldn't cope with the minute movements and would end up messy.  :wink:

Offline Welshbreed

  • Posts: 360
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Motorsport Service & Repair Level 3 Technician
    • @MrSmeeZus
  • Referrals: 0
Sealants and stuff
« Reply #8 on: June 11, 2007, 15:28:31 »
Quote from: "screwloose"
Plumbers mait would not be of use in the applications described I am afraid. It is primarily a jointing seal for threaded pipework. Used between floor plates for example, it wouldn't cope with the minute movements and would end up messy.  :wink:


Yeah must agree, i did think of it though (as Im a plumbing student)





 






SimplePortal 2.3.5 © 2008-2012, SimplePortal