AuthorTopic: Series bulkhead patching and clutch question  (Read 1693 times)

0 Members and 1 Guest are viewing this topic.

Offline MTyrrell

  • Posts: 366
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Series bulkhead patching and clutch question
« on: September 08, 2005, 21:14:13 »
I’ve just been to have a look at a friends SIII landy which he's looking at getting back on the road (Been parked behind his house for over a year and a half)

 One of the main points is the bulkhead and door pillar on the passenger’s side. There is a hole about half an inch in diameter just under the window screen bracket on the passengers side and one of the door pillars is also beyond repair and will need replacing, how easy is it to patch a bulkhead and replace a door pillar?

I know some one who's a welder so the welding bits sorted.

 Also the clutch has packed up. The peddle is sitting about an inch off the floor when you depress the clutch the noise from the thrust bearing stops and you can select a gear but when the clutch is released there is no drive. I'm assuming this is a clutch plate problem anybody else have any thoughts?

At the moment he's considering getting shot of the old girl inlight of these problems, but it seams a shame the amount of work he's allready done.
Regards
Matthew

www.cbpsystems.co.uk/(updated: quite often)
"Growing old is mandatory, growing up is optional"
<p>
In the dark it is better to be lead by a blind man! So in this age of insanity is it better to be lead by a mad man?

Offline Dr Neil

  • Posts: 818
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +1/-0
  • Referrals: 0
Series bulkhead patching and clutch question
« Reply #1 on: September 08, 2005, 21:23:45 »
it sounds like the clutch maybe seized since it's been standing for so long, or maybe the slave cylinder?it might be worth removing the slave cylinder and whilst holding it get an assistant to gently depress the clutch pedal, that way you will know whether the cylider is seized or if the hydraulic system is causing the fault.
Whilst the slave cylinder is out you could try and see if you can move the release bearing manually.If the hydraulic system is o.k but the release bearing doesn't move you may need to remove the gearbox....
hope this helps, regards Neil.....
200tdi over 200kmiles
+2"lift.
Procomp Es9000 shocks
235 MT's on silver modulars
diff guards
tank guard
Paidia4x4 winch bumper.
Discoparts HD rear bumper.
Champion 10000N winch
CB and CDplayer
Safari snorkel
modified turbo actuator vac pipe pick up.
twin batteries with Paidia4x4 split charge system
roof lightbar

Offline ian_s

  • Posts: 969
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Series bulkhead patching and clutch question
« Reply #2 on: September 09, 2005, 09:50:56 »
silly question, but is the transfer box in gear?
i've been caught out by that more than once  :oops:

as for the bulkhead, if you can get the front wing off, and take the door and screen off, i think its one the easier parts to weld, because you can get all around where you need to weld. and if your welders good, then there really shouldnt be a limit to what can be replaced
series 3 - 200tdi
Discovery V8

Offline MTyrrell

  • Posts: 366
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Series bulkhead patching and clutch question
« Reply #3 on: September 16, 2005, 23:22:42 »
Thanks for the info,
 Will be going to change the break master cylinder on it this weak end. I’ll try your suggestions for the clutch. Will also have a proper look at the bulkhead and see how much ill need to cut out.

cheers
matt
Regards
Matthew

www.cbpsystems.co.uk/(updated: quite often)
"Growing old is mandatory, growing up is optional"
<p>
In the dark it is better to be lead by a blind man! So in this age of insanity is it better to be lead by a mad man?

Offline MTyrrell

  • Posts: 366
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Series bulkhead patching and clutch question
« Reply #4 on: September 19, 2005, 10:37:51 »
Got some pics of the damage this weekend, these are the bits we are going to patch/replace.
Regards
Matthew

www.cbpsystems.co.uk/(updated: quite often)
"Growing old is mandatory, growing up is optional"
<p>
In the dark it is better to be lead by a blind man! So in this age of insanity is it better to be lead by a mad man?

Offline Miniman

  • Posts: 1638
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Series bulkhead patching and clutch question
« Reply #5 on: October 11, 2005, 22:04:20 »
Have you had a bash at the chassi with a hammer. Rear chassi usualy the worst.
WATER DRAWS LAND ROVERS LIKE IRON FILINGS TO A MAGNET
************************************
110 300tdi Everyday car.
90 200TDI Toy
Series3 90 look alike Project.
Skipton North Yorkshire



D E F R A. Destroying English Farming and Rural Areas.

Offline MTyrrell

  • Posts: 366
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Series bulkhead patching and clutch question
« Reply #6 on: October 12, 2005, 21:49:51 »
Quote from: "Miniman"
Have you had a bash at the chassi with a hammer. Rear chassi usualy the worst.


 Yep had a poke around, the rear cross member has gone across the back and the rear chassis rail will not last for ever.
 He's put the old girl up on eBay as she stands, Shame but she was starting to turn in to a bit of a money pit :(
Regards
Matthew

www.cbpsystems.co.uk/(updated: quite often)
"Growing old is mandatory, growing up is optional"
<p>
In the dark it is better to be lead by a blind man! So in this age of insanity is it better to be lead by a mad man?

Offline Miniman

  • Posts: 1638
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Series bulkhead patching and clutch question
« Reply #7 on: October 12, 2005, 22:03:57 »
When I bought my landy it took me 2 days on the ramp at work to weld the rear chassis 3 full days to weld the bulkhead up on the drive and 3 Months to get all the rest sorted Brakes , Bearings , lights , engine , ect ect and I am still at it now. Just been in the shed with my old gearbox pulling it to bits to find out what went wrong....Hummm Bits all over...

I LOVE MY LANDY....

I am not getting rid it more fun than a car...
WATER DRAWS LAND ROVERS LIKE IRON FILINGS TO A MAGNET
************************************
110 300tdi Everyday car.
90 200TDI Toy
Series3 90 look alike Project.
Skipton North Yorkshire



D E F R A. Destroying English Farming and Rural Areas.

Offline jimthelandyman

  • Posts: 447
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Series bulkhead patching and clutch question
« Reply #8 on: October 13, 2005, 21:40:43 »
have you tried adjusting the clutch there is an adjuster on the back of the master cylinder, although if it goes into gear then it can't be adjustment or you may have transfer box or overdrive in nuetral if it has one.

 






SimplePortal 2.3.5 © 2008-2012, SimplePortal