Pages: [1]   Go Down

AuthorTopic: fitting a torque convertor  (Read 898 times)

0 Members and 1 Guest are viewing this topic.

Offline jasonforsythe

  • Posts: 53
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
fitting a torque convertor
« on: June 02, 2010, 10:50:48 »
yes its me again!!!!
when i fit my convertor to the gearbox is it just a case of slipping it on all the way or am i looking for some kind of locking noise

thanks again

jason :afro:
Logged

Offline fuzzy

  • Posts: 82
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • my lovely s3 military, Percy
  • Referrals: 0
Re: fitting a torque convertor
« Reply #1 on: June 02, 2010, 17:29:42 »
hi, everyone is trying to help but it is very hard when you are posting threads all over the shop, not being funny, but if you were this clueless about doing the work on the motor, why did you start, you would have been better off getting professional help from the start. As i said, not being funny, just an observation. :rolleyes:
Logged
1980 s111 109 ex military 12v gs soft top- waiting to have life breathed back into it.
1990 110 2.5td, waiting for crew cab conversion, mud tyres, suspension and 2"lift.

Offline jasonforsythe

  • Posts: 53
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Re: fitting a torque convertor
« Reply #2 on: June 02, 2010, 20:16:49 »
not clueless  just not used to land rovers thats all but thanks for your comment anyway ,just 15 yrs since my city and guilds diploma thats all
and i do thank all for trying to help its just time and the hope to get it on the road again that brings me to ask you guys ,who knows maybe i will know something that you need !!
Logged

Offline fuzzy

  • Posts: 82
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • my lovely s3 military, Percy
  • Referrals: 0
Re: fitting a torque convertor
« Reply #3 on: June 02, 2010, 20:28:54 »
righty-o mate, no probs, i hope it all works out for you.
Logged
1980 s111 109 ex military 12v gs soft top- waiting to have life breathed back into it.
1990 110 2.5td, waiting for crew cab conversion, mud tyres, suspension and 2"lift.

Offline Scott-ie-dog

  • Posts: 14
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Re: fitting a torque convertor
« Reply #4 on: June 02, 2010, 23:57:54 »
Yep, just a matter of slipping it on, you need to slide it on the 2 splines then make sure the lugs are located properly for the oil pump. Turn it round making sure it has located fully.  The oil pump lugs are very important as i've seen a couple of people not do this and force the engine + box together destroying the pump resulting in fitting a new gearbox.
Logged

Offline Scott-ie-dog

  • Posts: 14
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Re: fitting a torque convertor
« Reply #5 on: June 03, 2010, 00:11:01 »
Just read the gearbox woes thread. Sounds like the pump has been destroyed already?
Logged

Offline jasonforsythe

  • Posts: 53
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Re: fitting a torque convertor
« Reply #6 on: June 03, 2010, 09:13:50 »
replaced the box and convertor and followed your instructions all done thanks for the reply now to put it all back again

ta jas
Logged
Pages: [1]   Go Up
 





SimplePortal 2.3.5 © 2008-2012, SimplePortal