I had been reading your posts with interest, any further updates?
Sorry, been doing a few more jobs :D
I 've fitted the CB into my Mud dash
I used a din mount which gives a good simple look to the dash
![Click to enlarge](http://inlinethumb19.webshots.com/44818/2734184820102123940S500x500Q85.jpg)
![Click to enlarge](http://inlinethumb57.webshots.com/43832/2374825530102123940S500x500Q85.jpg)
I've used a side mount on the back of the roof with a Orbitor antenna.
![Click to enlarge](http://inlinethumb29.webshots.com/44380/2154409750102123940S500x500Q85.jpg)
Then it was time for a big install
First job was to fit a rear work light
![Click to enlarge](http://inlinethumb22.webshots.com/43669/2527440460102123940S500x500Q85.jpg)
Followed by my new fibreglass headlining :mrgreen:
![Click to enlarge](http://inlinethumb33.webshots.com/46752/2829520620102123940S500x500Q85.jpg)
![Click to enlarge](http://inlinethumb57.webshots.com/44856/2438763650102123940S500x500Q85.jpg)
![Click to enlarge](http://inlinethumb11.webshots.com/44810/2365920950102123940S500x500Q85.jpg)
And my new roof console
![Click to enlarge](http://inlinethumb38.webshots.com/44197/2243906230102123940S500x500Q85.jpg)
I had to cut the headlining to fit the console. The two are not instantly compatable as the console is designed around the Land Rover headlining
![Click to enlarge](http://inlinethumb16.webshots.com/5519/2483324780102123940S500x500Q85.jpg)
![Click to enlarge](http://inlinethumb18.webshots.com/45457/2105485440102123940S500x500Q85.jpg)
The cb has been relocated up into the console so i put the blanking tray back into the mud dash
![Click to enlarge](http://inlinethumb51.webshots.com/46066/2634990360102123940S500x500Q85.jpg)
Headlining is looking rather smart
![Click to enlarge](http://inlinethumb23.webshots.com/43926/2615630500102123940S500x500Q85.jpg)
The finish looks like this
![Click to enlarge](http://inlinethumb27.webshots.com/46426/2575828660102123940S500x500Q85.jpg)
I installed a passenger grab handle too.
![Click to enlarge](http://inlinethumb06.webshots.com/43781/2765764930102123940S500x500Q85.jpg)
You have to trim the sun visors down when fitting the roof console
![Click to enlarge](http://inlinethumb55.webshots.com/43574/2545257390102123940S500x500Q85.jpg)
![Click to enlarge](http://inlinethumb09.webshots.com/44104/2426042580102123940S500x500Q85.jpg)
I fitted a 100 amp alternator
![Click to enlarge](http://inlinethumb12.webshots.com/46667/2831050700102123940S500x500Q85.jpg)
Then i began the ply lining of the load area.
![Click to enlarge](http://inlinethumb16.webshots.com/46095/2605761050102123940S500x500Q85.jpg)
![Click to enlarge](http://inlinethumb55.webshots.com/47478/2445910770102123940S500x500Q85.jpg)
The Series sides have ribs that run along the length which i used to fix some baton too
![Click to enlarge](http://inlinethumb47.webshots.com/46190/2696169930102123940S500x500Q85.jpg)
![Click to enlarge](http://inlinethumb34.webshots.com/45089/2357119280102123940S500x500Q85.jpg)
![Click to enlarge](http://inlinethumb01.webshots.com/46720/2932360310102123940S500x500Q85.jpg)
Now that the basic walls are in place i can start planning the lay out of the rear. There will be accessory sockets in there for the fridge and so on.
I'll do the flooring soon then find some material to cover it all.
Then i'll insulate the walls, seal the panels in and get some edging on the ply.
i have fitted my new rear diff guard :dance:
![Click to enlarge](http://inlinethumb14.webshots.com/43981/2799869810102123940S500x500Q85.jpg)
Its a ARB Dana 60 cover which fits like a glove
Just got to get a D44 one for the front axle now
i fitted some much nicer, original looking heated mirrors
I brought a couple of new mirror heads and drilled through the bottom
![Click to enlarge](http://inlinethumb17.webshots.com/17104/2372580170102123940S500x500Q85.jpg)
Took the mirrors apart and stuck heater pads on the back
![Click to enlarge](http://inlinethumb04.webshots.com/46211/2856145010102123940S500x500Q85.jpg)
Added a decent length of wire then rebuilt them
![Click to enlarge](http://inlinethumb09.webshots.com/46024/2868193920102123940S500x500Q85.jpg)
![Click to enlarge](http://inlinethumb02.webshots.com/43905/2805119260102123940S500x500Q85.jpg)
Then drill down through the ball section of the mirror arm
And the underside if the arm into the hinge
![Click to enlarge](http://inlinethumb55.webshots.com/46710/2502021640102123940S500x500Q85.jpg)
![Click to enlarge](http://inlinethumb64.webshots.com/16831/2669959670102123940S500x500Q85.jpg)
![Click to enlarge](http://inlinethumb04.webshots.com/14019/2908851840102123940S500x500Q85.jpg)
Remove the door hinge bolts and open hinge
![Click to enlarge](http://inlinethumb31.webshots.com/15326/2195758770102123940S500x500Q85.jpg)
Route the wire through a p clip
![Click to enlarge](http://inlinethumb28.webshots.com/44059/2691660360102123940S500x500Q85.jpg)
In through the bulk head
![Click to enlarge](http://inlinethumb11.webshots.com/47306/2742945800102123940S500x500Q85.jpg)
Once both sets of wire were in the car i removed the top of the dash to feed the wires to the Mud dash
![Click to enlarge](http://inlinethumb37.webshots.com/45860/2448190270102123940S500x500Q85.jpg)
![Click to enlarge](http://inlinethumb52.webshots.com/36467/2580001490102123940S500x500Q85.jpg)
![Click to enlarge](http://inlinethumb27.webshots.com/43738/2279581500102123940S500x500Q85.jpg)
The switch, relay and fuse were already in place from my previous install
![Click to enlarge](http://inlinethumb57.webshots.com/45688/2233707980102123940S500x500Q85.jpg)
To celebrate i gave it a birthday wash and polish
![Click to enlarge](http://inlinethumb20.webshots.com/37139/2734668080102123940S500x500Q85.jpg)
Now for the winch
First job was to replace the sagging springs with some HD Land Rover springs, new dampers and some D44 HD turret rings
![Click to enlarge](http://inlinethumb54.webshots.com/47157/2040003750102123940S500x500Q85.jpg)
Then i fitted a Milemarker SEC-8 winch
![Click to enlarge](http://inlinethumb16.webshots.com/45711/2598522410102123940S500x500Q85.jpg)
I stripped of the wire rope ready from my Plasma rope
![Click to enlarge](http://inlinethumb05.webshots.com/45444/2629926100102123940S500x500Q85.jpg)
For security i have installed a HD battery isolator switch
![Click to enlarge](http://inlinethumb01.webshots.com/45376/2662590590102123940S500x500Q85.jpg)
![Click to enlarge](http://inlinethumb01.webshots.com/44608/2726360700102123940S500x500Q85.jpg)
![Click to enlarge](http://inlinethumb43.webshots.com/45802/2298804180102123940S500x500Q85.jpg)
I want to install winch switches on the dash and use my Warn wireless remote to operate the winch so i replaced the solenoid pack and fitted a Allbright contactor
![Click to enlarge](http://inlinethumb61.webshots.com/43068/2773607770102123940S500x500Q85.jpg)
![Click to enlarge](http://inlinethumb04.webshots.com/46147/2323495610102123940S500x500Q85.jpg)
![Click to enlarge](http://inlinethumb57.webshots.com/45688/2233707980102123940S500x500Q85.jpg)
You can now see its sits nice and level
![Click to enlarge](http://inlinethumb11.webshots.com/45514/2822760400102123940S500x500Q85.jpg)
![Click to enlarge](http://inlinethumb34.webshots.com/43937/2988769770102123940S500x500Q85.jpg)
![Click to enlarge](http://inlinethumb54.webshots.com/44533/2992499080102123940S500x500Q85.jpg)
More to follow
![afro :afro:](http://www.mud-club.com/Smileys/default/afro.gif)