Fun, Friendly and Free
Welcome,
Guest
. Please
login
or
register
.
1 Hour
1 Day
1 Week
1 Month
Forever
Login with username, password and session length
News:
Forum back online. Please post!
Home
Forum
Battle
Search
Login
Register
Mud-club
»
Vehicle & Technical
»
Discovery
»
Eventually got round to fitting my side exit exhaust - 30+ photos.
Print
Pages: [
1
]
Go Down
Author
Topic: Eventually got round to fitting my side exit exhaust - 30+ photos. (Read 19330 times)
0 Members and 1 Guest are viewing this topic.
auf_wiedersehen_pet
Posts: 1179
Attack: 100
Defense: 100
Attack Member
Karma: +0/-0
Referrals: 0
Eventually got round to fitting my side exit exhaust - 30+ photos.
«
on:
May 04, 2009, 21:49:24 »
I was one of the many people who followed
this thread
about side exit exhausts.
Eventually I plucked up the courage and bought a pile of bits including a
Flexi Exhaust Tube,
Stainless Steel Roll Tip Exhaust Trim,
Stainless Steel Exhaust Adaptor Reducer Sleeve
Devon 4x4 Stainless Steel Exhaust Finisher
Exhaust Clamps Various.
Chequer Plate 5 Door Set.
After much head scratching I started with the chequer plate if I went wrong this would hide everything. I put a couple of rivets in my chequer plate and popped it into position. I marked out the chequer plate hole, took the plate of and cut the hole. I held it back in place to mark the bodywork and cut a hole in that too. I bolted the exhaust ring on and took a picture.
To get it spot on I used a grinder to flatten the ribs on the chequer plate so that the exhaust ring would sit flat against the plate.
My intention was to do a variation on the camel cut theme. To do this I sliced about 20mm off the leading edge of the chequer plate at the bottom and nothing at the top. Have a look at the photo to see what I mean.
I marked the same cut on the body and sliced that too. While I was at it, I ground the tail pipe off! I cut the straight section behind the wheel – about half way along.
The stainless steel exhaust adaptor reducer sleeve which I ordered from a company on eBay was supposed to be a tube which changed from one size to another – 150mm long. What I got was a 300mm “adapter” with the correct sizes at the end but a random bit in the middle!! There was no way that I could hide this behind the bodywork so it had to be mitred.
I worked out the angle by bolting two bits of shelving together and pushing it down the end of the exhaust and measuring the angle with the bodywork/
With this angle, I cut the adapter and welded it. (Fibber Alert – Okay, I got it welded in Fareham for £20).
The exhaust trim was good but needed shortening. It finished up at about 100mm.
Then, crunch time – bolt it all together. I did grind slots into the adapter so that it would compress when clamped.
Don’t worry – the jubilee clip bracket did not last long. I fabricated a 5mm thick bracket and fitted two rubberised exhaust mounts to eliminate vibration.
I also but an extra clamp on the adapter and longer L shaped brackets on the back of the exhaust ring.
One can of satin Hammerite and here it is when finished.
And the camel cut too.
Under compression……….
What do you think?
«
Last Edit: July 17, 2010, 12:52:37 by auf_wiedersehen_pet
»
Logged
Rob Steele
1995
Land Rover Discovery 300 TDi
- Everyday Car (Ex Jap)
2007
Toyota Avensis 2.2 T-180
- Sensible Car (Ex TSB Bank)
lee celtic
Regional Rep
Posts: 2680
Attack: 100
Defense: 100
Attack Member
Karma: +0/-0
Referrals: 0
Re: Eventually got round to fitting my side exit exhaust - 30+ photos.
«
Reply #1 on:
May 04, 2009, 22:19:15 »
Very tidy mate :clap: :clap: :clap:
Logged
so many hills , so little time ....
discovery TD5
work in progress...lol
Disco-Ron
Posts: 1048
Attack: 100
Defense: 100
Attack Member
Karma: +0/-0
Referrals: 0
Re: Eventually got round to fitting my side exit exhaust - 30+ photos.
«
Reply #2 on:
May 04, 2009, 22:42:36 »
I bet that makes the bodywork resonate nicely....!!
Also, when i did my camel cut i reflanged the arch to add strength, you'll find you'rs is now quite flimsy i suspect..... i would also taper out the sharp edge you've left on the arch return, it may not touch the tyre now, but when moving the bushes allow for movement, and it's not nice having to replace tyres due to cuts in them...... so simply taper the egde off and it'd be better.....
Logged
gone from 200tdi.... to 300tdi... still with loads done to it, in fact, even more than the last truck...LOL!!!
muddymud
Posts: 229
Attack: 100
Defense: 100
Attack Member
Karma: +0/-0
Referrals: 0
Re: Eventually got round to fitting my side exit exhaust - 30+ photos.
«
Reply #3 on:
May 05, 2009, 15:30:21 »
looking sweet mate, you really need to trim the strip of metal under the chequer plating it looks a bit odd.
Logged
Disco_Stu
Posts: 402
Attack: 100
Defense: 100
Attack Member
Karma: +0/-0
Any chance of a tow...?
Referrals: 0
Re: Eventually got round to fitting my side exit exhaust - 30+ photos.
«
Reply #4 on:
May 06, 2009, 00:37:28 »
Nice job Rob, like what you did with the angled exhaust.
I'm glad my initial thread helped bit and you've definitely taken it one step further. As it happens, my flexi pipe sheared off after 12 months, a little too much stress and not enough support on it I think.
Mark II will be a thing of beauty....
Stu.
Logged
1994 300Tdi Disco
Snorkel now complete....
http://forum.difflock.com/viewtopic.php?t=1906&highlight=
jjsaul
Posts: 1534
Attack: 100
Defense: 100
Attack Member
Karma: +0/-0
Leeds, West Yorks
Referrals: 0
Re: Eventually got round to fitting my side exit exhaust - 30+ photos.
«
Reply #5 on:
May 06, 2009, 03:12:52 »
The exhaust and the plate looks really good, i'd echo what other people have said about the wheelarch though.
Logged
James
...lovin dirty days out...
1983 OneTen V8 Station Wagon 3.5 (LPG)
1972 Range Rover V8
1992 Range Rover 4.6 (LPG)
1978 Range Rover Carmichael Commando 6x4
1972 Range Rover - Major project, FOR SALE
1976 Range Rover - Less of a project, FOR SALE
Previously: Range Rovers 1988, 1990 and others...
2005 Volvo V70 T5 SE (LPG) - daily driver
chiboy
Posts: 79
Attack: 100
Defense: 100
Attack Member
Karma: +0/-0
Referrals: 0
Re: Eventually got round to fitting my side exit exhaust - 30+ photos.
«
Reply #6 on:
September 24, 2009, 00:43:40 »
Bringing this old one back , heres mine
«
Last Edit: September 24, 2009, 00:46:57 by chiboy
»
Logged
Green 3.9 v8 Auto on LPG,Green Range Rover LSE Wheels , Roof lights ,Big bore S/S Exhaust , Winch bumper, Spot lights, CB, Safari snorkle,steering guard,jate rings,235,70,16 BFG mud terrains,diff guard, saudi spec grill, 2"LIFT Discoparts tree sliders QT Bonnet pod, 10,000lbs WINCH WITH PLASMA ROPE AND REMOTE
4wheelin
Posts: 1
Attack: 100
Defense: 100
Attack Member
Karma: +0/-0
Redditch Worceshire
Referrals: 0
Re: Eventually got round to fitting my side exit exhaust - 30+ photos.
«
Reply #7 on:
February 12, 2014, 23:16:32 »
Hi All New to Club we fabricate D1 Aftermarket products, We are based in Redditch Worcs, just perfected the side exit exhaust and available for
http://www.4wheeln.co.uk/shop2/product.php?id_product=595
We do many items visit my web site www,4wheelin.co.uk
http://www.4wheeln.co.uk/shop2/img/p/595-1249-thickbox.jpg
Logged
Print
Pages: [
1
]
Go Up
Mud-club
»
Vehicle & Technical
»
Discovery
»
Eventually got round to fitting my side exit exhaust - 30+ photos.
SimplePortal 2.3.5 © 2008-2012, SimplePortal