Pages: [1]   Go Down

AuthorTopic: Quick question about bolts  (Read 1300 times)

0 Members and 1 Guest are viewing this topic.

Offline brixworth-alan

  • Posts: 162
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • The new acquisition
  • Referrals: 0
Quick question about bolts
« on: October 21, 2008, 19:50:30 »
Another of my stupid questions- now I have drilled out my rusty bolts holding the hinges on I'm ready to tap the holes ready for replacements. But what spec are they? I thought they were 5/16 BSF but it turns out they aren't.....Haynes manual is no help.
Logged

Offline Rich_P

  • Posts: 1310
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Re: Quick question about bolts
« Reply #1 on: October 21, 2008, 20:31:19 »
You won't get very far trying to tap them.  The hinges are held on by captive nuts that slot into the bulkhead, you need to get another set of them and remove the old ones before fitting the new.
Logged

Offline brixworth-alan

  • Posts: 162
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • The new acquisition
  • Referrals: 0
Re: Quick question about bolts
« Reply #2 on: October 23, 2008, 19:38:00 »
There doesn't seem to be a straightforward way to get at the captive nuts to replace them. If fact I've already tapped the holes- just with the wrong size tap (very slightly too small)
Logged

Offline Rich_P

  • Posts: 1310
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Re: Quick question about bolts
« Reply #3 on: October 23, 2008, 19:44:32 »
They should just unclip and slip out of a square rectangular hole between the two holes in the bulkhead.
Logged

Offline brixworth-alan

  • Posts: 162
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • The new acquisition
  • Referrals: 0
Re: Quick question about bolts
« Reply #4 on: October 24, 2008, 20:48:22 »
Aha! Didn't think of that....thanks!
Logged

Offline Lucy1978

  • Posts: 516
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Re: Quick question about bolts
« Reply #5 on: October 25, 2008, 14:46:33 »
part numbers are...

79221 for the screw
MRC2178 for the captive nut

doesn't say what thread though
Logged

Offline brixworth-alan

  • Posts: 162
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • The new acquisition
  • Referrals: 0
Re: Quick question about bolts
« Reply #6 on: October 26, 2008, 22:07:16 »
I'm rather struggling with this unclipping business- there doesnt seem to be enought space to slide teh captive nut up to the hole.

What am i doing wrong?
Logged

Offline baron von ledwidge

  • Posts: 143
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Re: Quick question about bolts
« Reply #7 on: October 30, 2008, 00:23:33 »
Have you tried twisting it as you pull it so you like slide it off and round out of the hole, if i remeber the holes are a little rectangular shaped, iff not they sould just bend out the way
Logged
Series iii 88"                Series 3 88"
2.25 diesel                  200tdi
 Hard top                     Exmoor Trim hood
checker plate wings     checker plate wings
checker plate sills        parabolic springs
checker plate floor       overdrive
                                    roll cage
                                    corabreu bucket seats   
                                    fairey overdrive
drive it break it fix it
Pages: [1]   Go Up
 





SimplePortal 2.3.5 © 2008-2012, SimplePortal