Pages: [1]   Go Down

AuthorTopic: Body repairs, newwing and chassis leg  (Read 1210 times)

0 Members and 1 Guest are viewing this topic.

Offline baron von ledwidge

  • Posts: 143
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Body repairs, newwing and chassis leg
« on: May 22, 2008, 20:14:22 »
I had alittle prang in my landy a while back and it needs a new wing and chassis leg fitting i was wandering howhard a job this would be to repair and if anyone had any advice on doing it
thanks
aaron
Logged
Series iii 88"                Series 3 88"
2.25 diesel                  200tdi
 Hard top                     Exmoor Trim hood
checker plate wings     checker plate wings
checker plate sills        parabolic springs
checker plate floor       overdrive
                                    roll cage
                                    corabreu bucket seats   
                                    fairey overdrive
drive it break it fix it

Offline lightweight-love

  • Posts: 403
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Re: Body repairs, newwing and chassis leg
« Reply #1 on: May 22, 2008, 21:33:16 »
depends if you can weld and have a welder really! new dumb iron(chassis leg) is under a tenner i think, new wing 20 maybe?
does it defo need replacing or could u just weld a new sleeve over the top?-might be a lot easier.
If you can weld its easyish but takes a while(lots of grinding and welding), wing is simple only a few bolts!
Logged
1975 s111 lightweight 200tdi, paras, snorkel, winch... My everyday ride
1976 s111 lightweight stock new restoration project :)
1974 s111 Long term restoration project, galv chassis, paras...
"she's not leaking oil, she's marking her territory"

Offline Rich_P

  • Posts: 1310
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Re: Body repairs, newwing and chassis leg
« Reply #2 on: May 23, 2008, 19:05:08 »
The biggest difficulty and also one of the most important parts about it is alignment, get it wrong and you'll have cocked up your suspension geometry.
Logged

Offline lightweight-love

  • Posts: 403
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Re: Body repairs, newwing and chassis leg
« Reply #3 on: May 23, 2008, 20:58:32 »
making up a jig helps wid alignment, how is ur chassis leg damaged really?
Logged
1975 s111 lightweight 200tdi, paras, snorkel, winch... My everyday ride
1976 s111 lightweight stock new restoration project :)
1974 s111 Long term restoration project, galv chassis, paras...
"she's not leaking oil, she's marking her territory"

Offline craftycarper

  • Posts: 62
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Re: Body repairs, newwing and chassis leg
« Reply #4 on: May 25, 2008, 20:30:09 »
cut the wing bolts off with a small grinder as all the muck gets up there and the bolts rust together, it saves a lot of time and bother piddling around with spanners, also don't forget if it's the drivers side then it should have a mudguard which has bolts throught it and the wing into the piller. As for the welding treat yourself to a mig and give it a bash, if you can plate it then great just make up a u/ box section and have a practice on a spare piece of plating first, Migs are a handy piece of kit, youre gonna need one for all sorts of jobs and will save you money in next to no time...check this link out for  tips and ideas.....good luck

http://www.mig-welding.co.uk/
Logged
Pages: [1]   Go Up
 





SimplePortal 2.3.5 © 2008-2012, SimplePortal