Pages: [1]   Go Down

AuthorTopic: Fitting Modulars on a LR Series 1 - Studs thin and short!!  (Read 1007 times)

0 Members and 1 Guest are viewing this topic.

Offline auf_wiedersehen_pet

  • Posts: 1179
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Fitting Modulars on a LR Series 1 - Studs thin and short!!
« on: April 03, 2007, 21:25:02 »
Evening all,

Seen a cracking Series 1 with Modulars. Much better stance.

Anyhow, bought some and the studs are a bit short and a bit thin for the modulars. Can I fit replacements easily?

Cheers

Rob
Logged
Rob Steele

1995 Land Rover Discovery 300 TDi - Everyday Car (Ex Jap)
2007 Toyota Avensis 2.2 T-180 - Sensible Car (Ex TSB Bank)

Offline auf_wiedersehen_pet

  • Posts: 1179
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Fitting Modulars on a LR Series 1 - Studs thin and short!!
« Reply #1 on: April 03, 2007, 21:38:01 »
Logged
Rob Steele

1995 Land Rover Discovery 300 TDi - Everyday Car (Ex Jap)
2007 Toyota Avensis 2.2 T-180 - Sensible Car (Ex TSB Bank)

Offline bob86

  • Posts: 57
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Fitting Modulars on a LR Series 1 - Studs thin and short!!
« Reply #2 on: April 03, 2007, 22:46:06 »
Quote from: "auf_wiedersehen_pet"
Seen these...

http://cgi.ebay.co.uk/LAND-ROVER-SERIES-PUSH-IN-TYPE-HUB-STUDS-x5_W0QQitemZ4524409006QQcategoryZ31348QQrdZ1QQssPageNameZWD1VQQcmdZViewItem

Would this do the trick?

Cheers

Rob


Those are larger in diameter but the same length.
Logged
1955 86" 200tdi series one,

Offline auf_wiedersehen_pet

  • Posts: 1179
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Fitting Modulars on a LR Series 1 - Studs thin and short!!
« Reply #3 on: April 04, 2007, 08:41:45 »
Thanks for point that out. I was ready to buy them!

Cheers

Rob
Logged
Rob Steele

1995 Land Rover Discovery 300 TDi - Everyday Car (Ex Jap)
2007 Toyota Avensis 2.2 T-180 - Sensible Car (Ex TSB Bank)

Offline bob86

  • Posts: 57
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Fitting Modulars on a LR Series 1 - Studs thin and short!!
« Reply #4 on: April 04, 2007, 18:33:37 »
I did do thats why i know. :roll:
To fit them you also need to recess the back of the hubs so the flange sits flush or they end up even shorter than the ones you have.
Logged
1955 86" 200tdi series one,
Pages: [1]   Go Up
 





SimplePortal 2.3.5 © 2008-2012, SimplePortal