Pages: [1]   Go Down

AuthorTopic: Heat shield under exhaust manifold?  (Read 653 times)

0 Members and 1 Guest are viewing this topic.

Offline Dr Strangeglove

  • Posts: 137
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Heat shield under exhaust manifold?
« on: February 18, 2007, 04:11:02 »
I have taken the heads of my V8 and whilst doing so a couple of bolts broke on the exhaust manifold (off side) towards the bulk head.  The screws in question were not standard.  They had a long head on them and were tapped so that a tray/shield of some kind could be bolted to them using a smaller diameter screw.  I could not see what the tray was shielding and I am wondering if this needs to go back on.  Has anyone any ideas?
Logged
Too many sins, not enough temptation!
Too many armpits, not enough deodorant!
Forget maths, forget geometry
You cause explosions by being good at Chemistry
Too many mountains, not enough volcanoes!
Too many lawyers, not enough justice!!!

Offline hairyasswelder

  • Posts: 1351
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • It's gonna cost ya
  • Referrals: 0
Heat shield under exhaust manifold?
« Reply #1 on: February 18, 2007, 21:04:22 »
Hi, Do you mean tyhe one sheilding the starter motor?

Steve
Logged
'88 RR 3.5 efi, an on going project :o) evolving daily/slowly

Offline Garth

  • Posts: 287
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Heat shield under exhaust manifold?
« Reply #2 on: February 19, 2007, 23:27:50 »
Just done my heads.  There should (used to be) a heat shield between the manifold and starter. There is also a bracket that goes onto the top bolt between 8 and 6.
Logged
"WINNE"
1991 VOUGE SE A WITH LPG
LOOKS GOOD (BUT LOOKS CAN BE DECEIVING)
"TIGGER"
1995 SUZUKI VITARA
1" LIFT
225/75X15 AT'S

Offline Dr Strangeglove

  • Posts: 137
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Heat shield under exhaust manifold?
« Reply #3 on: February 20, 2007, 08:18:16 »
Thanks - I will make sure it goes back on - unfortunately I broke them trying to take them out :cry:
Where is the best place to get new bolts for the exhaust (including the extended ones for this) and also the steel items that have the tabs on to stop the bolts from becoming loose?
Logged
Too many sins, not enough temptation!
Too many armpits, not enough deodorant!
Forget maths, forget geometry
You cause explosions by being good at Chemistry
Too many mountains, not enough volcanoes!
Too many lawyers, not enough justice!!!

Offline Range Rover Blues

  • Moderator
  • ***
  • Posts: 15218
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +3/-0
    • South Yorkshire
  • Referrals: 0
Heat shield under exhaust manifold?
« Reply #4 on: February 20, 2007, 16:40:59 »
Try Rimmers Bros for stuff like that, not the cheapest but if they say it's in the post, it's in the post.  Otherwise D4x4.
Logged
Blue,  1988  Range Rover 3.5 EFi with plenty of toys bolted on
Chuggaboom, 1995 Range Rover Classic
1995 Range Rover Classic Vogue LSE with 5 big sticks of Blackpool rock under the bonnet.
Pages: [1]   Go Up
 





SimplePortal 2.3.5 © 2008-2012, SimplePortal