AuthorTopic: Petrol to diesel  (Read 1959 times)

0 Members and 1 Guest are viewing this topic.

Offline ukmudmaster

  • Posts: 293
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
    • Billericay Essex
  • Referrals: 0
Petrol to diesel
« on: June 30, 2005, 21:00:23 »
I have a 2 1/4 petrol S3 SWB and I want a diesel! Does the 2.5 N/A diesel fit my gearbox?? the tank has a hole for the return pipe, electics are no problem. I would be grateful for any info,
thanks,
Dave
Range Rover Classic EFI auto, 3.9 V8 Offroader, 300 Tdi Auto greenlaner.
axledeep@googlemail.com

Offline Dr Neil

  • Posts: 818
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +1/-0
  • Referrals: 0
Petrol to diesel
« Reply #1 on: June 30, 2005, 22:46:56 »
i believe it will, though after playing round Tixover in Stanton Boys i'd be very tempted to fit a 200tdi if you can find one!!!
if you have any questions on fitting the tdi contact Stanton Boy, he'll be glad to try and help/advise you, i'm sure.
200tdi over 200kmiles
+2"lift.
Procomp Es9000 shocks
235 MT's on silver modulars
diff guards
tank guard
Paidia4x4 winch bumper.
Discoparts HD rear bumper.
Champion 10000N winch
CB and CDplayer
Safari snorkel
modified turbo actuator vac pipe pick up.
twin batteries with Paidia4x4 split charge system
roof lightbar

Offline Xtremeteam

  • Regional Rep
  • *
  • Posts: 6476
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Its just the way i roll
    • lampeter, west wales
  • Referrals: 0
Petrol to diesel
« Reply #2 on: June 30, 2005, 22:55:08 »
ur not getting my tdi unless its very crisp pound notes as ive just finished building it lol
Mike
I can Drive.. You can criticize..
I too can criticize like you.. but can you Drive like me??


Offline cstokes

  • Posts: 167
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Petrol to diesel
« Reply #3 on: June 30, 2005, 23:09:45 »
It is quite straight forward to fit either 2.5n/a or 2.5td from a defender or the 200tdi from either a defendr or a disco but the disco engine is alot more difficult to fit because of the turbo location and the exhaust, you will have to remove the battery tray from the chassis to make room for the diesel pump, with the 2.5n/a ot td you can use the series radiator but you will need to loose the viscous coupling, with the tdi you need to try and accomodate the intercooler which can be tricky. other than that it is quite easy as you can use the series mountings and bolt them straight onto the new engine.  If you need any more info just give us a shout.   I fitted a disco 200tdi into my series short wheel base and it now flies.

Offline ep90

  • Posts: 65
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Tdi conversion
« Reply #4 on: July 01, 2005, 07:12:10 »
Is the 300 Tdi harder to fit then the 200?  Most of the 200 Tdi's I've seen advertised are high mileage (due the thier age I guess)  Will a 200/300 bolt staight to my 2A box?

Thanks

Offline cstokes

  • Posts: 167
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Petrol to diesel
« Reply #5 on: July 01, 2005, 22:01:08 »
I don't know about the 300tdi,  but the 200tdi will fit on to your box, what you need to do is use the 200tdi clutch pressure plate with the series 2a friction plate.  On the diesel pump side of the engine there is a gearbox mounting stud in the bell housing that needs to be removed.

You will also have to fit four studs into the bottom of the bell housing if it is a disco engine as on the disco it uses four long through bolts and these don't line up with the series gearbox.

Offline matthew

  • Posts: 494
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Petrol to diesel
« Reply #6 on: September 02, 2005, 03:54:37 »
Did you use Disco or Defender manifolds and turbo?
Cheers

Matthew
1958 Ser II  88" 1962 Ser IIa 109" 1962 Ser IIa 109" Dormobile
www.buryautoclub.co.uk | www.torquebac.co.uk | www.oldlandrovers.co.uk | www.oldroads.co.uk | http://lancsglass.oldroads.co.uk

Offline cstokes

  • Posts: 167
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Petrol to diesel
« Reply #7 on: September 05, 2005, 20:59:01 »
I used the disco inlet and exhaust manifolds,  Inlet is not an issue, but you will have to cut the cast front pipe and rotate it about 1/2" clockwise to clear the chassis rail, you will the have to fabricate an exhaust system.
Every thing else clears. Radiator and inter cooler are all a little tricky, but it just a matter of finding the best fit.  I ditched the viscous fan and fitted electric fan instead, much easier. if you require any info just drop us a pm.
 i don't mind taking photo's if this helps.

Offline Miniman

  • Posts: 1638
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Petrol to diesel
« Reply #8 on: September 26, 2005, 22:59:20 »
I have a Series 3 2.25Diesel and I would not recomend it for power as I run out of steam when going up steep hills yeh go for the 200tdi
WATER DRAWS LAND ROVERS LIKE IRON FILINGS TO A MAGNET
************************************
110 300tdi Everyday car.
90 200TDI Toy
Series3 90 look alike Project.
Skipton North Yorkshire



D E F R A. Destroying English Farming and Rural Areas.

 






SimplePortal 2.3.5 © 2008-2012, SimplePortal