AuthorTopic: Thermostat or Muff needed?  (Read 3206 times)

0 Members and 1 Guest are viewing this topic.

Offline Suvvey

  • Posts: 369
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Thermostat or Muff needed?
« on: December 20, 2009, 11:57:14 »
Well it's thick in snow outside and the temperature is not getting much above freezing but unfortunately neither is the motor :-. Noticed that since the temperature has plumetted outside I am struggling to get the needle out of the cold white line. The only time this has been able to move off the line is whilst travelling over 50mph on the clear roads and only if able to do this uninterupted. As soon as I slow to below 40mph it drops right back down again :? Obviously being a draughty defender the heater struggles at the best of times but It's barely thawing inside at the moment.

I checked that the fan coupling is letting it free wheel and it is so I'm guessing this is either the Thermostat stuck open or maybe even just to be expected and time to make up a muff for the front? But surely this is more likely the thermostat as what would happen if it really was cold out there (-4 to 0 out there now)?
« Last Edit: December 20, 2009, 15:25:48 by Suvvey »

Success is the ability to go from one failure to another with no loss of enthusiasm.
-- Winston Churchill--

'93 Defender 110 County

Offline suggs

  • Posts: 1050
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Re: Thermostat or Muff needed?
« Reply #1 on: December 20, 2009, 14:21:22 »
i take it you have a tdi, its pretty normal for this weather mines the same, i checked my state and its working fine and dumped the coolant and have filled with new antifreeze no airlocks etc nd still runs cold. i asked this on another forum and most tdi owners said theres were the same...
modded 90

V8 Disco 2 ES premium for the Mrs

Offline Suvvey

  • Posts: 369
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Re: Thermostat or Muff needed?
« Reply #2 on: December 20, 2009, 14:58:49 »
Yes, it's a 200tdi. Only replaced the thermostat, pump and coolant 6 months ago so was a bit anoyed that maybe the stat had gone already. Guess this means I'm going to be cutting up some old carpet tonight then :roll:

Success is the ability to go from one failure to another with no loss of enthusiasm.
-- Winston Churchill--

'93 Defender 110 County

Offline trecfive

  • Posts: 457
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • If it fit's the hook it'll pull it.
    • Nuneaton
  • Referrals: 0
Re: Thermostat or Muff needed?
« Reply #3 on: December 20, 2009, 15:07:05 »
Remove the cooling fan and carry it in the back(with the spanner)that will improve it a bit more,when it warms up outside put it back on again, put a post-it note on the dash to remind you if you tow anything to replace the fan.
1. Range Rover Classic 300tdi SE Auto Softdash
2. Range Rover Classic 300tdi SE Auto Softdash, apparently very rare.

Offline Range Rover Blues

  • Moderator
  • ***
  • Posts: 15218
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +3/-0
    • South Yorkshire
  • Referrals: 0
Re: Thermostat or Muff needed?
« Reply #4 on: December 20, 2009, 15:10:01 »
It's simply that your enghine is nit burning enough fuel to keep warm, or put another way your heater is that efficient it overcools the engine.  The radiator is probably not even getting warm.

I had the same in my Cavalier, It was toasty and warm blasting to Hull every day but when I hit the traffic it would cool down significantly by the time I got to work.  In traffic the 'rad barley got warm.
Blue,  1988  Range Rover 3.5 EFi with plenty of toys bolted on
Chuggaboom, 1995 Range Rover Classic
1995 Range Rover Classic Vogue LSE with 5 big sticks of Blackpool rock under the bonnet.

Offline Suvvey

  • Posts: 369
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Re: Thermostat or Muff needed?
« Reply #5 on: December 20, 2009, 15:23:38 »
I did try it with the heater turned off and it made a little difference but still no where near what I'd expect. I'm sure the boys in LR knew what they were doing but surely the stat should open at a higher temp than it is, to keep the engine at a healthy operating temperature? I am assuming that the sender is on the engine side of the system and not on the rad side :-. Have to admit I can't picture where it is now :oops: My td5 at work never struggles to get warm.
« Last Edit: December 20, 2009, 15:27:46 by Suvvey »

Success is the ability to go from one failure to another with no loss of enthusiasm.
-- Winston Churchill--

'93 Defender 110 County

Offline william127

  • Posts: 424
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Re: Thermostat or Muff needed?
« Reply #6 on: December 20, 2009, 16:52:13 »
id just be glad its not at the other end of the scale :)
1990 defender 127 flatbed 200tdi mud tyres stripdown started 14/03, now striped, ned to start the expensive bit
1992 rrc vogue se izuzu 2.8td running well so it got sold,
2003 110 td5 hardtop,ex mod, arived 25/04, bfg a/ts, ply lined, k and n filter, honda sport seats, rear demountable 2000lb winch, security grills,high lift with winching kit, mountney small steering wheel, momo gear knob, front spots, airhorns, hd steering, diff guard, ex army  center towpin bumper replaced with winch bumper, rear mounted bottle opener, cheaquer plate, neon underbody light, ex police map light,1000 watt inverter, reversing camera
2007 ford ranger wildtrack d/cab(dads)
yamaha big bear 350 2wd, likes to eat flies, fixed (until i roll it again)

Offline tack43

  • Posts: 351
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
    • Worcs, Redditch
  • Referrals: 0
Re: Thermostat or Muff needed?
« Reply #7 on: December 20, 2009, 20:02:55 »
I had a simular problem. Took the stat out and it had "82" stamped on it. Replaced with an 88 deg stat which improved it. I now also have a kenlowe fan which has impoved it more.

Rich
Rich

1985 90 300TDI "Defender" SOLD.
1990 RRC 3.9 Vogue LPG
1991 RRC 3.9 Vogue SE "The spare parts box!" Broken for spares
1993 RRC Off-roader. No engine. Yet!
1991 RRC 3.9 Vogue SE "Tempory off-roader" Failed MOT - More spare parts
1992 RRC 3.9 Vogue SE "New tempory off-roader" SOLD

Offline bogie

  • Posts: 695
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • IF IT AINT GOT LEAFS,ITS NO GOOD!!!!!!!!
  • Referrals: 0
Re: Thermostat or Muff needed?
« Reply #8 on: December 21, 2009, 20:34:53 »
Throw the viscus away and go for a elecy fan!
1968 SERIES 2A ,200TDI TUNED,RANGE ROVER AXLES,ONE TON SHACKLES,CPC PARAS,ES3000,POLYBUSHED,ANACONDAS.                     1970 SERIES 2A, 200TDI TUNED,5 SPEED LT77 WITH LT230S TRANSFER BOX 1.211 RATIO.ZEUS DISKS ALLROUND.ES3000,MODIFIED 90 TANK,3.5 DIFFS.

Offline graham2306

  • Posts: 554
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Re: Thermostat or Muff needed?
« Reply #9 on: December 21, 2009, 21:49:29 »
The electric fans on Misubishi FTOs are brilliant, they have two speeds and fit on a land Rover rad a treat with a couple of brackets fabricated from dexion or similar.

I have one on my Disco 200Tdi engined Defender and this time of year I never turn it on.
It's not a real car unless it's over 30 years old!
Classic cars are the ones who's owners wave to each other. I just bought a pretend car! F plate 90!

N.Oxon GLASS Rep

Offline Saffy

  • Posts: 3127
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +1/-0
    • The Bell Inn, Imber.
  • Referrals: 0
Re: Thermostat or Muff needed?
« Reply #10 on: December 22, 2009, 07:34:26 »
My temp gauge was in the normal temp with the weekends laning and road travels.  Rad muff was fully closed (nothing to do with the cold but to stop Plains sludge blocking rad). I didn't have the heater on at all, and was mostly driving around with window open (eberspacher diesel furnace keeps things super toasty).

But I still think it's worth checking your thermostat as it not unheard off for even a new/recent one to be duff. Further maybe strap a sturdy plastic sack to front grill - see what happens as easy experiment. I still wonder what the effect is by blocking the flow through the intercooler along with rad... overfueling if pump is previously tweaked? seems to smoke more *Dunno*.
Wouldn't ditch a working viscious fan myself, not with a tdi but that topic usually starts a flame war (someone will come along with CAPSLOCK on and say they circumnavigated the Sun without a fan fitted and even got 45mpg to boot ;))  Same vain I do not think leccy fan belongs in an all-terrain vehicle. Seen a fair amount of leccy fans failing to start on trucks during laning days because mostly they are rarely used and get cruded up with the terrain, others are just bad installations.
« Last Edit: December 22, 2009, 07:45:05 by Magical Tanglefoot Pow! Pow! »
.swonk eno oN .esoht dna eseht ,siht dna taht ,wollof ot selur emos teg eW

Offline Range Rover Blues

  • Moderator
  • ***
  • Posts: 15218
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +3/-0
    • South Yorkshire
  • Referrals: 0
Re: Thermostat or Muff needed?
« Reply #11 on: December 23, 2009, 03:28:35 »
And leccy fans can't shift anywhere near as much air as a viscous.  The engineers at Kenlowe told me NOT to remove my viscous in favour of twin leccy fans.

Anyhoo, another effect of the cold weather is that the air going into your engine is colder, it should make it more efficient but it also chills the cylinder head.
Blue,  1988  Range Rover 3.5 EFi with plenty of toys bolted on
Chuggaboom, 1995 Range Rover Classic
1995 Range Rover Classic Vogue LSE with 5 big sticks of Blackpool rock under the bonnet.

Offline Suvvey

  • Posts: 369
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Re: Thermostat or Muff needed?
« Reply #12 on: December 23, 2009, 06:21:52 »
Well unfortunatel I've noticed that my average mpg has gone from a healthy 31/32 to 27 so I think the engine is struggling as it never warms up properly. I'm convinced the stat must be open so will get one today. Even if it makes no difference at least I will still have a spare :roll:

Success is the ability to go from one failure to another with no loss of enthusiasm.
-- Winston Churchill--

'93 Defender 110 County

Offline denviks

  • Posts: 1219
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Re: Thermostat or Muff needed?
« Reply #13 on: December 23, 2009, 11:27:26 »
i just had the same on my 300 tdi disco..... i swapped out the stat for a 89 degree one and i now have a nice warm heater again.... so much so i need to turn it down now  :lol:

if you change your stat atleast you should have peace of mind its done
cheers
dennis
more moves than a dad in a disco!!!!!!!!!!


im always @ www.plcuk.co.uk

Offline Suvvey

  • Posts: 369
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Re: Thermostat or Muff needed?
« Reply #14 on: December 23, 2009, 14:24:20 »
Well I went to local moto factors today and they didn't have one :roll: Thought I'd try Halford's for a laugh and they did :shock: Only thing is that when I checked it at home it was an 82 degree one rather than 88 and also was missing the sprung flange on the bottom :-k. Bit pee'd off but guess I should off checked before I left, but at least I now had a gasket so decided to did out the old (6 months!) one.
There was a small deposit stuck in the stat but don't think this would of been enough to cause much if any coolant to pass through. Took it inside to test and it seemed fine. Didn't have a thermometer to test it accurately but it seemed to be reluctant to open far even in freshly boiled water.
Any hoo's it's all back together now. Just popped in to have a bite for lunch and then out to give it a test drive so fingers crossed [-o<

Success is the ability to go from one failure to another with no loss of enthusiasm.
-- Winston Churchill--

'93 Defender 110 County

Offline V8MoneyPit

  • Moderator
  • ***
  • Posts: 5077
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +1/-0
  • Referrals: 0
Re: Thermostat or Muff needed?
« Reply #15 on: December 23, 2009, 14:58:38 »
Didn't have a thermometer to test it accurately but it seemed to be reluctant to open far even in freshly boiled water.

Noooo..... you shouldn't really dump it in boiling water. I understand it can damage them. You should bring the temp up gradually and check it opens before the water boils. in the same vein, ff your car boils for some reason, it is always advisable to change the stat in case it has been damaged.
Rgds
Steve

"Reality is wrong. Dreams are for real."

Land Rover build:
www.daisythediesel.com

Photos (my other passion and weakness):
http://www.flickr.com/photos/v8moneypit/

Offline Suvvey

  • Posts: 369
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Re: Thermostat or Muff needed?
« Reply #16 on: December 23, 2009, 17:16:50 »
Well maybe it was what the doctor ordered as it seems to be working now :lol: Just have to keep an eye on it when the weather warms up and make sure it doesn't start overheating if I have knackered it.
Got up to just over 1/3 on the gauge which is where it usually sits and didn't deviate too much after that. Definately never got down to the cold mark once it had warmed up and the heater was much warmer (notice I didn't use the word 'hotter' :lol:) although admittedly the ambient temp outside is probably 5 or more degrees warmer than it has been.
On the downside I do now seem to have an issue with the sender or possibly the wire from it as there is now the occasional sudden drop in temp on the gauge that is far too fast to be an actual reading. Obviously I did have a good look around the area whilst doing the stat and I did notice that the sender does seem to move very slightly in it's housing which may be the issue, also the spade connector looked like it could of done with a tighten up and probably a clean. I don't think this was the original problem as I can definately feel more heat from the heater but more likely from me knocking around in the engine bay :oops:

Success is the ability to go from one failure to another with no loss of enthusiasm.
-- Winston Churchill--

'93 Defender 110 County

Offline Suvvey

  • Posts: 369
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Re: Thermostat or Muff needed?
« Reply #17 on: January 05, 2010, 17:09:46 »
My earlier optimism was short lived and probably self induced as I don't think anything really changed much other than maybe a few degrees warmer outside :roll: Decided to give a muff a try and luckily found an old tent bag that was exactly the right size and even came with clips that fitted the grill in just the right way to keep it secure and tight with no modification :afro: Infact I was very impressed with my quick handywork (aka 'bodge'). Also it did make a lot of difference during road use, keeping the needle above the cold line and usually around the 1/4 way mark. Unfortunately when I went laning on Sunday in particularly cold weather it struggled to get above the line again.
Yesterday I was lucky enough to have to drop my work Td5 off at our not so local independant LR specialist so bought another stat. Fitted it today and thought I'd take the long way home to see if it got up to temp.
I DIDN'T EVEN GET A MILE FROM WORK before it was sitting on the half way mark AND it was -2 outside :shock: Firstly I thought something was going terribly wrong and it was going to over heat but it stayed bang on half way all the way home no matter how fast or slow I was going and even when I parked up for a while it only dropped a fraction. Now this tells me that the old stat had been duff from the moment I first installed it 6months ago as it would only ever just get off the cold mark by the time I'd done the 4 miles to work in the morning and this was during the summer :doh:
Toasty hot in the cab now :dance: So much so I actually had to turn the heat down by the time I got home. Not a day to soon either looking the weather that is meant to be coming in :twisted:

Success is the ability to go from one failure to another with no loss of enthusiasm.
-- Winston Churchill--

'93 Defender 110 County

Offline pondy653

  • Posts: 126
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
    • Norwich
  • Referrals: 0
Re: Thermostat or Muff needed?
« Reply #18 on: January 05, 2010, 20:45:32 »
Nice one mate,
Thanks for Sunday by the way you did a stirling job.

TC
98 Defender 110 CSW Tdi
Audi A3 Sportback 2.0 TDI Sport DSG
Yamaha WR450F (for treading really lightly)
4x4 Response (Norfolk&Suffolk) Member since 1999

Offline bogie

  • Posts: 695
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • IF IT AINT GOT LEAFS,ITS NO GOOD!!!!!!!!
  • Referrals: 0
Re: Thermostat or Muff needed?
« Reply #19 on: January 06, 2010, 20:34:16 »
GO FOR THE MUFF!!!!!!!!!!!!
1968 SERIES 2A ,200TDI TUNED,RANGE ROVER AXLES,ONE TON SHACKLES,CPC PARAS,ES3000,POLYBUSHED,ANACONDAS.                     1970 SERIES 2A, 200TDI TUNED,5 SPEED LT77 WITH LT230S TRANSFER BOX 1.211 RATIO.ZEUS DISKS ALLROUND.ES3000,MODIFIED 90 TANK,3.5 DIFFS.

Offline zulublue

  • Posts: 756
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Re: Thermostat or Muff needed?
« Reply #20 on: January 06, 2010, 22:57:50 »
I don't run a fan on a 200Tdi, digital stat never goes over 83 enen in the summer, 200's run cool normally

Offline bogie

  • Posts: 695
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • IF IT AINT GOT LEAFS,ITS NO GOOD!!!!!!!!
  • Referrals: 0
Re: Thermostat or Muff needed?
« Reply #21 on: January 07, 2010, 21:02:56 »
Same here mate!
1968 SERIES 2A ,200TDI TUNED,RANGE ROVER AXLES,ONE TON SHACKLES,CPC PARAS,ES3000,POLYBUSHED,ANACONDAS.                     1970 SERIES 2A, 200TDI TUNED,5 SPEED LT77 WITH LT230S TRANSFER BOX 1.211 RATIO.ZEUS DISKS ALLROUND.ES3000,MODIFIED 90 TANK,3.5 DIFFS.

Offline mudplugger01

  • Posts: 65
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Re: Thermostat or Muff needed?
« Reply #22 on: January 07, 2010, 22:56:19 »



same here  no fan  200 tdi  100 % veggie oil lol
110 sw 1984 ,200 tdi ,5 speed,bio diesel crewcab fedima tyres,8274 ,nearly sorted lol..just need .............

Offline bogie

  • Posts: 695
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • IF IT AINT GOT LEAFS,ITS NO GOOD!!!!!!!!
  • Referrals: 0
Re: Thermostat or Muff needed?
« Reply #23 on: January 08, 2010, 21:35:45 »
LAUGHIN WIT YA!!!!!!!!!!!!!!!!!!!!!!
1968 SERIES 2A ,200TDI TUNED,RANGE ROVER AXLES,ONE TON SHACKLES,CPC PARAS,ES3000,POLYBUSHED,ANACONDAS.                     1970 SERIES 2A, 200TDI TUNED,5 SPEED LT77 WITH LT230S TRANSFER BOX 1.211 RATIO.ZEUS DISKS ALLROUND.ES3000,MODIFIED 90 TANK,3.5 DIFFS.

 






SimplePortal 2.3.5 © 2008-2012, SimplePortal