Mud-club

Vehicle & Technical => Mitsubishi => Topic started by: rr bitsa on December 06, 2004, 12:04:11

Title: pully replacement
Post by: rr bitsa on December 06, 2004, 12:04:11

The bottom pully on my 2.8td Has come off.How do I put it back on and how can I tighten it so that it can,t  come off again.
Any advice appreciated
Thanks Paul

Title: pully replacement
Post by: EvilEd on December 06, 2004, 13:43:26

If it's the one I thing it is, grind a mm or two off the bolt and use locktight or similar... the bolts have a habit of being a bit long and using the end of the bolt rather than the head to keep them tight.

Title: pully replacement
Post by: rr bitsa on December 06, 2004, 13:51:11

Thanks,But its not the complete pully that has come off.Its just the outer ring which appears to be held on by pressure and a rubber type ring on the inside.

Title: pully replacement
Post by: EvilEd on December 06, 2004, 14:14:03

Try going here:
http://www.pocuk.com/phpBB2/search.php
put in Bottom Pully and select the All Words option.

Loads of info on it but always seems to be the bolt.

Might be worth ringing http://www.milners.co.uk as well.

Title: pully replacement
Post by: rr bitsa on December 06, 2004, 14:45:20

Thankyou evil ed.Looks like I need a new pully then.
Cheers Paul

Title: pully replacement
Post by: J B on December 06, 2004, 18:59:18

if the pulleys come appart then you do need a new one

unfortunatly it is a very expensive part, you may need to try a few scrapy's

good luck

ta jon

Title: pully replacement
Post by: Darren.B on December 06, 2004, 19:24:04

Give these guys a try

www.gt4x4.com

hth Darren

Title: pully replacement
Post by: rr bitsa on December 06, 2004, 19:46:47

Thankyou all, Am trying to source one now.Also is it easy to get whats left off the block.
Cheers Paul

Title: pully replacement
Post by: J B on December 06, 2004, 21:49:03

if its anything like the 2.5 pulley, then its quite easy

just put 2 longish m8 bolts through the pulley where the second ring bolts on, and just keep winding each one gently to bottom out the bolts onto the,

ahh i wuold have said bottom cam belt pulley but as yours is chain drive i'm not sure never stipped a 2.8

mmm

not sure then, sorry

Title: pully replacement
Post by: GrimReaper on December 07, 2004, 06:44:23

Have you tryed these for a replacement >>>>>> http://www.milneroffroad.com/ ........ hth

Title: pully replacement
Post by: rr bitsa on December 09, 2004, 09:45:56

Thankyou all.
Got one being delivered from milner tomorrow.Now have to try and get whats left of the old one off.
Cheers Paul

Title: pully replacement
Post by: EvilEd on December 09, 2004, 11:04:31

Good luck mate, hope it goes okay.

Try and make sure you use a 6point socket on the bolt rather than a 12 or 18 as it is usually very tight and you'll round the bolt with multipoint sockets.

Don't forget to shorten the new bolt too and put some threadlock on there.

You might want to do a before and after shot of your knuckes too..... Just so you remember what they used to look like :)

EvilEd

Title: pully replacement
Post by: rr bitsa on December 09, 2004, 14:28:57

Cheers evil ed.Need to get a socket to fit first. none of the ones i have that fit are strong enough.Knuckles they are only cosmetic.
Cheers Paul