Mud-club
Vehicle & Technical => Range Rover => Topic started by: barriesheene on September 24, 2007, 13:02:30
-
Hey guy's, I'm having a few prob's with Paddock spare's :roll: Been waiting a week for a water hose pipe not delivered when told e.t.c. e.t.c. Anyway my question is this. I've removed 4 belt's from my rangie but paddock are telling me that I should only have 3 ! Any idea's :?: I should be getting my bit's at last tomorrow so I'll let you know what I get :evil:
-
I've had problems too with paddocks. Normaly they are good. I only have 3 on my 3.9 efi clasic.
Do you have air con?
Rich
-
Yep ! It's an '89 efi classic 3.9 v8
-
mine an '88 3.5 and I have 4 \:D/
one from crank to water pump, one crank to power steer, power steer to alt and one from water pump to air con. :wink:
Steve
-
mine an '88 3.5 and I have 4 \:D/
one from crank to water pump, one crank to power steer, power steer to alt and one from water pump to air con. :wink:
Steve
Theres no need to dance, there are 2 reasons I dislike that design.
1 You have to remove 3 belts just to change one of them (guess which one I've had problems with :( )
2 If the watter pump belt breaks you have no warning on those 4 belt V8s where as engines with one belt for water and alternator if it breaks then the red light comes on giving you some warning rather than a few minuets latter when the engine temperature starts to soar.
I lied, I've remembered a third
3 by the time you've taken the slack out of the PAS belt then theri is bearly enough adjustment on the alterator with new belts and old belts there is none left.
-
Theres no need to dance, there are 2 reasons I dislike that design.
:cry: sorry
-
Theres no need to dance
OK may have come across a little too strong :oops:
-
:? So to get the correct belt's am I going to have to go to landrover ? I've got the three coming from paddock's but god knows what use they are going to be :roll: I know what you mean clbarclay. It was a hell of a potch just to get the old ones off :roll: But thank's for having four also hairy arse even if it is only a 3.5 :wink:
-
http://www.gates.com/part_locator/index.cfm?location_id=3002 hows that for service :wink:
Would seem the link does not save the details but it says 4 belts and gives Gates part no.s
clbarclay... only kidding :wink:
If you dislike the v belts that much why not convert them to the multi v :wink: Thought about it but other things took priority, plus I got outbid on the complete set on e-bay :roll:
Just for reference it lists the same belts/part no.s for 3.5 and 3.9 and 2 of the belts are the same part no. :shock:
-
I bought Gates belts form my local motor factor recently for the same system......
Pretty cheap too AFAIR.
-
thanks for the link hairy :wink: Look's as tho I've got two the same and one slightly diffrent.No alternator belt by the look of thing's cos that's alot smaller :roll: I'll check tomorrow and let you know. Oh and the rear brake pads look wrong to cos there's nowhere for the pins to go through. Look's as tho they got the water hoses right :evil:
-
thanks for the link hairy :wink: Look's as tho I've got two the same and one slightly diffrent.No alternator belt by the look of thing's cos that's alot smaller :roll: I'll check tomorrow and let you know. Oh and the rear brake pads look wrong to cos there's nowhere for the pins to go through. Look's as tho they got the water hoses right :evil:
No worrie :wink:
Pins dont go through :wink: they just hold the spring clips looks silly till you have a look on the car but they have a taper/ radius to match the caliper.
You'll see when you take the wheel off :wink:
It seems that they are better over the counter than mail order as they always spot on when I go there :?
Steve
-
Ok update peep's :lol: Hoses changed,havnt had chance to look at pads yet :roll: Belt's Hmmmmmm :oops: Changed fan belt and power steering belt but now the power steering seem's alot heavier than it was before I changed the belt ?????? Belt not slipping now mind so no sudden loss of power just alot less than I had before,( roundabout's are now not so scary with a sudden loss of steering :shock: ) But I've kinda caused another problem :roll: I had to remove the dizzy cap to get to the hoses behind that i had to change and now it wont go on properly :evil: If I remove the rotor arm it goes on fine, but with the arm in place the cap wont sit on the dizzy properly ?? The arm is on fine and as far down the spindle as it will go. I've managed to force the clips back on the cap and the engine run's but with a lack of power and the cap is moving slightly with the engine running and not flush with the dizzy body it's as if the cap shrunk while it was off the car. I've had to run it to work today but i should imagine the rotor arm is chewing it's way through the cap. There is no obvious reason why it wont go on as it came off ok and the actual dizzy hasn't been touched. help please :cry:
-
It happens on the Lucas dizzy, when you pull the arm off the centre of the dizzy pulla out a little too :(
It's bust then though :cry: