Topic: just fitted a 3" lift kit but,,,,,,,,, (Read 3672 times)

jamesey · « **on:** February 25, 2009, 16:43:09 »

i have 2 issues , ive fitted the 3" kap springs and fitted rhino rays cranked radius arms but now the rear steering arm rubs the radius arms , how do i get over this , also the front panhard bolt that goes into the threadded part of the front axel has rounded and i cant tighten the front passenger side up??
and just 1 more thing will i need a front prop shaft extension as the toothed bit on the front rubber is showing?????

glaggs · « **Reply #1 on:** February 25, 2009, 17:37:14 »

1 - check your rear srearing ling is straight - there should still be clearance?
2 - Your going to have to do a thread repair - Helicoil or similar.
3 - You need a spacer, D+G do them, but I guess some one will do them in the UK cheaper.

jamesey · « **Reply #2 on:** February 25, 2009, 18:34:07 »

whats a rear srearing ling

glaggs · « **Reply #3 on:** February 25, 2009, 22:45:06 »

My crap typing... should read

....rear steering link ....

jamesey · « **Reply #4 on:** February 26, 2009, 08:56:46 »

just got off the phone with darren at kap and he said that the front radius arms are wrong , the arms were from rhino rays and i need to take them off , :-> thats another £150 waisted , he said there angled too much and i need to put the standard arms back on and stregthen them and just put some proper bushes in , also the threadded bolt hole in the axel he said i need to chop it out :shock:and weld another in

last picture is the bolt thats spinning , and its the pre mounted nut in the axel not the nut thats treaded this needs to be tight or wham :x

jamesey · « **Reply #5 on:** February 26, 2009, 19:07:13 »

just turned the steering left to right it rubbs on the prop where it is on the steering arm when i turn the wheel full lock to the right , and rubs on the radius drivers side to the left

mlines · « **Reply #6 on:** February 27, 2009, 08:45:38 »

There really is something not right with your setup and I am not convinced its the Rhino Ray arms. They are certainly curved up but not to an extent where the arms should rub.

Here is mine....

As you can see, the steering arm is near the diff but a long way from the radius arm and it would have to be one hell of a curve to move it that much

Martin

jamesey · « **Reply #7 on:** February 27, 2009, 11:32:02 »

do you have standard arms on martin , do you have the castor corredtion bushes , and i wonder if the arms ive fitted are the rear ones????if so ive been mis sold them and thell be going back :->

mlines · « **Reply #8 on:** February 27, 2009, 11:59:22 »

Mine are standard arms fitted with correction bushes

Martin

jamesey · « **Reply #9 on:** February 27, 2009, 15:12:57 »

i thuink ive been sold the rear arms by mistake :roll: would they do this

glaggs · « **Reply #10 on:** February 27, 2009, 20:17:56 »

Talk to them, they should swap them for you. The std arms are easily bent or broken so heavy duty ones are best.

jimny gary · « **Reply #11 on:** February 28, 2009, 13:55:08 »

I had castor corrected arms for a 4" lift on my last jimny (from DG tuning) and the rear steering link was nowhere near touching the radius arms, I'd send them back for a refund.
I have castor correction bushes on my current jimny and I feel theyre on the limit with a 2" lift really, I think you still need a set of castor corrected arms with a new 3" lift kit.
(Martins jimny has the extra weight of his cage and winches to weigh the suspension down a bit)

Gary

jamesey · « **Reply #12 on:** February 28, 2009, 16:29:45 »

ive had them 2 long now and ive no reciept for them , i wonder if i can put some correction bushes in to bring it back. whos arms do they look like? im sure there from rhino rays

jimny gary · « **Reply #13 on:** February 28, 2009, 20:54:26 »

they do look a bit rhino ray ish.... they look like standard arms that have been cut and bent, then strengthened back up with plate to me. I'd still talk to him about taking them back or credit note if youve had them a while, they look bent.

Gary

jamesey · « **Reply #14 on:** March 01, 2009, 19:48:42 »

i think they look bent because the shocks arnt on in the pic and the front axel is down but trust me there not bent there new.
ive been told by a jimny man near me that the arms i have are designed for a 2" lift , so does anybody want them. ill have to buy some kap ones

£££££££££££££ :doh:

jimny gary · « **Reply #15 on:** March 02, 2009, 21:37:38 »

designed for a 2" lift? thats about 1 degree away from a 3" lift... so they should be nearly exactly the same. As for KAP items, check that your buying castor corrected arms rather than just heavy duty.

Gary

jasonslaphead · « **Reply #16 on:** March 19, 2009, 13:46:36 »

your arms dont look anything like like the rhino rays ones at all.

jamesey · « **Reply #17 on:** March 19, 2009, 16:26:45 »

these were the old design , ive had them over a year or more dont 4get :clap:

jasonslaphead · « **Reply #18 on:** March 19, 2009, 18:49:48 »

The reason I posted the picture was because of what you said in your previous post.

Quote from: jamesey on February 28, 2009, 16:29:45

whos arms do they look like? im sure there from rhino rays

jamesey · « **Reply #19 on:** March 20, 2009, 17:30:42 »

ive sold them now to a guy whos going to put offsett rubbers in

News:

AuthorTopic: just fitted a 3" lift kit but,,,,,,,,, (Read 3672 times)