Pages: [1]   Go Down

AuthorTopic: Series 3 wiring loom  (Read 4484 times)

0 Members and 1 Guest are viewing this topic.

Offline CanIBeFrank

  • Posts: 109
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Series 3 wiring loom
« on: February 12, 2007, 22:10:13 »
Hi,

Where can I buy a new series 3 wiring loom?

Diesel 88" Series III 1982. With a 2.5 N/A fitted.

Thanks
Logged

Offline reriessandlover

  • Posts: 69
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
wiring loom
« Reply #1 on: February 12, 2007, 22:22:24 »
if you find out let me know as well mine is a bit shot
Logged
series 3
perkins prima powered
parabolics
procomp es3000

Offline hobbit

  • Posts: 4750
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Series 3 wiring loom
« Reply #2 on: February 13, 2007, 03:34:04 »
Found this one

http://www.autoelectricsupplies.co.uk/about

Someone near me has recently purchased a new loom for his s3 88", not sure on the price though, will get some info off him tomorrow
Logged
Kev

'91 stretch Discovery 200 Tdi
Hybrid for running round (got to go now)
Srs 3 Lightweight petrol (got to go)
Srs 3 Lightweight petrol, runabout

Not every problem can be solved with duct tape, and it's exactly for those situations we have WD 40

Offline CanIBeFrank

  • Posts: 109
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Series 3 wiring loom
« Reply #3 on: February 13, 2007, 10:51:39 »
Thanks Hobbit be good if you could let me know when you find out, much appreciated.
Logged

Offline philbert

  • Posts: 212
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Series 3 wiring loom
« Reply #4 on: February 13, 2007, 19:27:02 »
try here this is where i got mine


http://www.autosparks.co.uk/
Logged

Offline CanIBeFrank

  • Posts: 109
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Series 3 wiring loom
« Reply #5 on: February 14, 2007, 10:06:47 »
Thanks Philbert,

Just out of interest for those reading this in the future the items required for a 1982 88" Diesel Series 3 are as follows;
 
From main harness to engine
LR333  RHD/LHD Engine Harness - Diesel  Ã‚£34.45
 
Main Harness including Ins panel and lights
LR 317 RHD Engine Bay Harness - Diesel   £139.92
 
Rear lights incl fogs etc
LR336  RHD/LHD Chassis Harness - SWB Petrol & Diesel  Ã‚£49.29
 
(Please note the above prices exclude VAT and delivery)  
NB: LR 333 is interchangable with 332 depending on engine sufix.

Personally I find this expensive but I've worked hard on the rest of the truck so it would be a shame not to finish it off properly  :shock:
Logged

Offline bob86

  • Posts: 57
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Series 3 wiring loom
« Reply #6 on: February 14, 2007, 19:44:00 »
I got a loom for my series 1 from autosparks. Its pretty good quality.
Logged
1955 86" 200tdi series one,

Offline CanIBeFrank

  • Posts: 109
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Series 3 wiring loom
« Reply #7 on: February 15, 2007, 10:18:33 »
Hi Bob86,

I dont doubt it, the guy I spoke to on the phone was extreamly helpful.

I have at least 2 1/2 looms currently fitted  :?  I should realy just bite the bullet and get it done properly before the whole thing just goes up in smoke.
Logged
Pages: [1]   Go Up
 





SimplePortal 2.3.5 © 2008-2012, SimplePortal