AuthorTopic: 2.5D psst noise  (Read 867 times)

0 Members and 1 Guest are viewing this topic.

Offline TechnoTurkey

  • Posts: 707
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
2.5D psst noise
« on: March 31, 2006, 16:31:39 »
When the engine is running it gives a regular pssst noise like air escaping under pressure.  Quicker when revs rise, there is also a bit of gunk around one of the injectors - is this problem likely to be serious?

Hope not as the engine is the only bit that runs ok!
2007 Honda Civic Type R GT
1982 VW Camper - Current Project
1991 Pajero SWB 2.5TD - SOLD
1990 Range Rover Vouge 3.9 V8 - SCRAPPED
1989 110 3.5 V8 CSW - SOLD
1984 Series 3, Ex MoD, 109 SOLD
1986 90 2.5D Pick Up - SOLD

Offline extreme90

  • Regional Rep
  • *
  • Posts: 3219
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • say no to orange extreme bits !!
  • Referrals: 0
2.5D psst noise
« Reply #1 on: March 31, 2006, 19:33:29 »
could be the brake servo pipe leaking ?
Dan Thomas,                  Matt Price
Team Relentless " No half measures "
Bobtailed Auto Td5 90 comp truck........... Got more tricks than a magician !!

http://www.Devon 4x4.co.uk >> for all your truck needs and more !!
http://www.Gigglepin4x4.net >> For when the going gets tuff, and one motor just isnt good enough !!!
http://www.gwynlewis4x4.co.uk >> the guy everyone forgets, but he doesnt forget your custom.

Offline TechnoTurkey

  • Posts: 707
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
2.5D psst noise
« Reply #2 on: April 03, 2006, 10:38:11 »
Thanks for that, I will have a proper look at it today/
2007 Honda Civic Type R GT
1982 VW Camper - Current Project
1991 Pajero SWB 2.5TD - SOLD
1990 Range Rover Vouge 3.9 V8 - SCRAPPED
1989 110 3.5 V8 CSW - SOLD
1984 Series 3, Ex MoD, 109 SOLD
1986 90 2.5D Pick Up - SOLD

Offline john b

  • Posts: 11
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
2.5D psst noise
« Reply #3 on: April 03, 2006, 13:24:23 »
sounds to me like one of the copper washers where the injector meets the block-has broken down i had the same on my200 tdi 90 a while ago made a sound like there was air escaping even on tickover

if you need to remove it use something like a hooked piece of welding wire or something similar to remove it and when you pu the new one back in use a piece of thin tubing that'll guide the new washer into the hole and placed back in the same location as the other one was

H T H

JOHN

Offline TechnoTurkey

  • Posts: 707
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
2.5D psst noise
« Reply #4 on: April 03, 2006, 15:53:00 »
Thanks, one of the injectors does have some gunk around it so I will have a look.
2007 Honda Civic Type R GT
1982 VW Camper - Current Project
1991 Pajero SWB 2.5TD - SOLD
1990 Range Rover Vouge 3.9 V8 - SCRAPPED
1989 110 3.5 V8 CSW - SOLD
1984 Series 3, Ex MoD, 109 SOLD
1986 90 2.5D Pick Up - SOLD

Offline hobbit

  • Posts: 4750
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
2.5D psst noise
« Reply #5 on: April 03, 2006, 20:33:14 »
Quote from: "TechnoTurkey"
Thanks, one of the injectors does have some gunk around it so I will have a look.


Try spraying some soapy water round it :wink:
Kev

'91 stretch Discovery 200 Tdi
Hybrid for running round (got to go now)
Srs 3 Lightweight petrol (got to go)
Srs 3 Lightweight petrol, runabout

Not every problem can be solved with duct tape, and it's exactly for those situations we have WD 40

 






SimplePortal 2.3.5 © 2008-2012, SimplePortal