AuthorTopic: Gear Box!!  (Read 2331 times)

0 Members and 1 Guest are viewing this topic.

Offline paul_humphreys

  • Posts: 2181
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Gear Box!!
« on: December 18, 2005, 15:56:34 »
I think I have broke my gearbox. I have a RRC with a 4 speed box. I pulled a 110 out of a hole 2 weeks ago, on the way home the box would lose all drive on over-run. Out in it today and the box kept loseing drive. I could get drive back by stoping and trying all gears. Could this be the clutch or the transfur box?

Also I can get hold of a LT230, well I know the 230 is right. Will this fit the 4 speed box if the transfur box has gone. Will I have to change the pops if it fits.

If all this is a balls up then I can get a whole RRC with VM2.4TD in and a 5 speed box.
LC 80 series 1993. 285/75/16s Cooper STTs, OME 850s on the front with 25mm packer, 868s on the rear. 4.88 diffs. Winch bumper with 12000lb winch. Factory lockers. HD rear bumper with wheel carrier and winch mount.

http://www.crag-uk.org


Offline Xtremeteam

  • Regional Rep
  • *
  • Posts: 6476
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Its just the way i roll
    • lampeter, west wales
  • Referrals: 0
Gear Box!!
« Reply #1 on: December 18, 2005, 18:28:16 »
right:

the rangie 4 speed box has the transfer box built into the back of the gearbox,u need to either swap the whole thing or you can rebuild the Tbox in place (did the centre diff on mine outside on a crappy day as it had exploded & locked up)

i have no idea if a 5 speed box is a straight swap,i hope it is cos i have a rangie 4 speed in my v8 90 & have been offerd a 5 speeder quite cheap
Mike
I can Drive.. You can criticize..
I too can criticize like you.. but can you Drive like me??


Offline paul_humphreys

  • Posts: 2181
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Gear Box!!
« Reply #2 on: December 18, 2005, 18:57:27 »
I know you need to move the gearbox mount on the one side, not sure if it needs drifrent gearbox cross member.

Paul
LC 80 series 1993. 285/75/16s Cooper STTs, OME 850s on the front with 25mm packer, 868s on the rear. 4.88 diffs. Winch bumper with 12000lb winch. Factory lockers. HD rear bumper with wheel carrier and winch mount.

http://www.crag-uk.org


Offline paul_humphreys

  • Posts: 2181
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Gear Box!!
« Reply #3 on: December 18, 2005, 19:56:54 »
By the way, my gear box dose not have a diff lock, it has a LSD in the gear box.

Paul
LC 80 series 1993. 285/75/16s Cooper STTs, OME 850s on the front with 25mm packer, 868s on the rear. 4.88 diffs. Winch bumper with 12000lb winch. Factory lockers. HD rear bumper with wheel carrier and winch mount.

http://www.crag-uk.org


Offline johnniep

  • Posts: 209
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Gear Box!!
« Reply #4 on: December 18, 2005, 20:10:05 »
hmmm, unlucky!!! i have one of these, but its done the oppostie to yours!, its stuck in 4wd, ive taken off the front prop so now i have a 3.5 tdi rearwheel drive rrc monster!
and its not a lsd, its a viscous coupling,
thats all i have to say o nthe matter!
cheers
johnnie p
rangie1, nissan 3.5tdi 4door vogue
rangie2, perkins 6cylinder 5.5litre disel 2door
rangie3, 3.5 v8 4door bobtail
rangie4, 2door engineless, probs b a special!

Offline paul_humphreys

  • Posts: 2181
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Gear Box!!
« Reply #5 on: December 18, 2005, 20:29:50 »
John, I through they did not put the viscous coupling in a 4 speed manual box? I know there something in there as it will drive with the front prop removed. My RRC was assembled in South Africa from a kit.

I will take it down to LEGS tomorrow to get told whats wrong and how much to fix. I might just change the compleat box for now.
LC 80 series 1993. 285/75/16s Cooper STTs, OME 850s on the front with 25mm packer, 868s on the rear. 4.88 diffs. Winch bumper with 12000lb winch. Factory lockers. HD rear bumper with wheel carrier and winch mount.

http://www.crag-uk.org


Offline johnniep

  • Posts: 209
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Gear Box!!
« Reply #6 on: December 18, 2005, 20:32:20 »
no, in the transferbox, im not sure, since it was assembled froma kit it may have been a choice of several bits?!?!?

cheers
johnniep
rangie1, nissan 3.5tdi 4door vogue
rangie2, perkins 6cylinder 5.5litre disel 2door
rangie3, 3.5 v8 4door bobtail
rangie4, 2door engineless, probs b a special!

Offline Xtremeteam

  • Regional Rep
  • *
  • Posts: 6476
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Its just the way i roll
    • lampeter, west wales
  • Referrals: 0
Gear Box!!
« Reply #7 on: December 18, 2005, 21:38:20 »
Quote from: "paul_humphreys"
John, I through they did not put the viscous coupling in a 4 speed manual box? I know there something in there as it will drive with the front prop removed. My RRC was assembled in South Africa from a kit.

I will take it down to LEGS tomorrow to get told whats wrong and how much to fix. I might just change the compleat box for now.

<Expletive deleted>,you have a dead rare box

my dad had one & it blew up & he fitted a standard box,what age exactly of rangie do you have??

if its 71-72 it prob will have a LSD for the centre diff,

if its a 85-onwards manual/auto it might have a borgwarner Tbox which has a viscous coupling
Mike
I can Drive.. You can criticize..
I too can criticize like you.. but can you Drive like me??


Offline johnniep

  • Posts: 209
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Gear Box!!
« Reply #8 on: December 18, 2005, 21:40:57 »
ahhh, i did have a lsd in the center diff in one of mine! that was a 71, but i ripped it appart in the woods and replaced it with a new one,they have a series of plates to fill up where the lsd went,
i see where your comeing from, didnt they stop it because it was costing too much? and it did work very well, untill it selfdestructed!!
cheers
johnnie p
rangie1, nissan 3.5tdi 4door vogue
rangie2, perkins 6cylinder 5.5litre disel 2door
rangie3, 3.5 v8 4door bobtail
rangie4, 2door engineless, probs b a special!

Offline paul_humphreys

  • Posts: 2181
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Gear Box!!
« Reply #9 on: December 18, 2005, 21:46:03 »
Its a 1980 but as I said it was put togeather in South Africa, so it could be anything in there. I do know it will drive with no front prop on as when the UJs on the front prop were done it was driven around with just the back prop on. So something must be locking the diff?

Paul
LC 80 series 1993. 285/75/16s Cooper STTs, OME 850s on the front with 25mm packer, 868s on the rear. 4.88 diffs. Winch bumper with 12000lb winch. Factory lockers. HD rear bumper with wheel carrier and winch mount.

http://www.crag-uk.org


Offline johnniep

  • Posts: 209
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Gear Box!!
« Reply #10 on: December 18, 2005, 21:48:10 »
when the centre diff went bang on mine, there was just a manged mess of bits, and that was holding it in 4wd, jus makeing loud clunting noised now and again and looseing drive but then would clunt and move again, that may be what it is then!!
johnnie p
rangie1, nissan 3.5tdi 4door vogue
rangie2, perkins 6cylinder 5.5litre disel 2door
rangie3, 3.5 v8 4door bobtail
rangie4, 2door engineless, probs b a special!

Offline paul_humphreys

  • Posts: 2181
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Gear Box!!
« Reply #11 on: December 18, 2005, 21:52:28 »
Quote from: "johnniep"
when the centre diff went bang on mine, there was just a manged mess of bits, and that was holding it in 4wd, jus makeing loud clunting noised now and again and looseing drive but then would clunt and move again, that may be what it is then!!
johnnie p


Well that sounds just like mine!!!

Mike, thats what i ment in the transfur box, the LSD. Th 4 speed box is all one unit I beleve?

Paul
LC 80 series 1993. 285/75/16s Cooper STTs, OME 850s on the front with 25mm packer, 868s on the rear. 4.88 diffs. Winch bumper with 12000lb winch. Factory lockers. HD rear bumper with wheel carrier and winch mount.

http://www.crag-uk.org


Offline johnniep

  • Posts: 209
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Gear Box!!
« Reply #12 on: December 18, 2005, 21:55:09 »
yes, it is all one unit, all cast in one peice, so either get hold of a new centre diff if it needs thatof replace the lot!, i had it hung off of a 6 cylinder 5.5ltre perkins desil so i found the 4speed to be the strongest and most reliable so i got a new standard centre diff, and it worked, but i do like the 5speed for the extra gearing you have on the road.
cheers
johnnie p
rangie1, nissan 3.5tdi 4door vogue
rangie2, perkins 6cylinder 5.5litre disel 2door
rangie3, 3.5 v8 4door bobtail
rangie4, 2door engineless, probs b a special!

Offline Xtremeteam

  • Regional Rep
  • *
  • Posts: 6476
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Its just the way i roll
    • lampeter, west wales
  • Referrals: 0
Gear Box!!
« Reply #13 on: December 18, 2005, 21:55:15 »
the rangie 4 speed is a 1 piece unit although the Tbox can be fixed (centre diff replaced) from undedrneath,just takes a wee bit o patience,not really that hard to do but then i have done a few
Mike
I can Drive.. You can criticize..
I too can criticize like you.. but can you Drive like me??


Offline paul_humphreys

  • Posts: 2181
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Gear Box!!
« Reply #14 on: December 18, 2005, 22:05:22 »
I dont have the time to fix it my self right now. I will take it down to LEGS tomorrow as its only a mile away to see what they say.

Thanks fron the info.
Paul
LC 80 series 1993. 285/75/16s Cooper STTs, OME 850s on the front with 25mm packer, 868s on the rear. 4.88 diffs. Winch bumper with 12000lb winch. Factory lockers. HD rear bumper with wheel carrier and winch mount.

http://www.crag-uk.org


Offline paul_humphreys

  • Posts: 2181
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Gear Box!!
« Reply #15 on: December 28, 2005, 21:24:57 »
Turned out I broke the Transfer box.

Paul
LC 80 series 1993. 285/75/16s Cooper STTs, OME 850s on the front with 25mm packer, 868s on the rear. 4.88 diffs. Winch bumper with 12000lb winch. Factory lockers. HD rear bumper with wheel carrier and winch mount.

http://www.crag-uk.org


Offline johnniep

  • Posts: 209
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Gear Box!!
« Reply #16 on: December 28, 2005, 21:26:31 »
which part of it? was it the lsd center diff? or the viscous coupling? how did you get it repaired?

cheers
johnnie p
rangie1, nissan 3.5tdi 4door vogue
rangie2, perkins 6cylinder 5.5litre disel 2door
rangie3, 3.5 v8 4door bobtail
rangie4, 2door engineless, probs b a special!

Offline Range Rover Blues

  • Moderator
  • ***
  • Posts: 15218
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +3/-0
    • South Yorkshire
  • Referrals: 0
Gear Box!!
« Reply #17 on: December 30, 2005, 02:27:25 »
BTW the 5 speed box with T-box is bigger than a 4 speed so you will need the tunnel from a later car.  These don't unbolt either so you'll need to be crafty.  They are also weaker than the 4 speed.
Blue,  1988  Range Rover 3.5 EFi with plenty of toys bolted on
Chuggaboom, 1995 Range Rover Classic
1995 Range Rover Classic Vogue LSE with 5 big sticks of Blackpool rock under the bonnet.

Offline paul_humphreys

  • Posts: 2181
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Gear Box!!
« Reply #18 on: December 30, 2005, 19:25:15 »
Quote from: "johnniep"
which part of it? was it the lsd center diff? or the viscous coupling? how did you get it repaired?

cheers
johnnie p


Not sure what part, but when it was off theres lots of bits in there!!!

I might just get rid and get my self a 110.

Paul
LC 80 series 1993. 285/75/16s Cooper STTs, OME 850s on the front with 25mm packer, 868s on the rear. 4.88 diffs. Winch bumper with 12000lb winch. Factory lockers. HD rear bumper with wheel carrier and winch mount.

http://www.crag-uk.org


 






SimplePortal 2.3.5 © 2008-2012, SimplePortal