Mud-club

Vehicle & Technical => Defender => Topic started by: Big G on September 20, 2012, 01:24:00

Title: Transfer box or Gearbox?
Post by: Big G on September 20, 2012, 01:24:00
1998 300 Defender
Some strange metallic noises occur intermittantly from this area. No problem selecting gears. Occasional bump and click sound when moving off.

Gearbox or transfer box on way out?

Best course of action?

All help appreciated.
Title: Re: Transfer box or Gearbox?
Post by: lambert on September 20, 2012, 05:03:48
Bump and click suggest one or more prop shaft universal joints, lift one wheel per axle and rotate appropriate prop back and forth by hand to check for play.
Title: Re: Transfer box or Gearbox?
Post by: Big G on September 20, 2012, 09:40:30
Mr Lambert Sir,

I will do exacerly as you suggest for a start. If I know all the UJs are good then take it from there. Other than the bump and click the other noise seems in time with propshaft, its a spinning tinkleing sound that comes and goes! Could this be down to a driveshaft UJ? One near the transfer box? Thanks so far by the way.
Title: Re: Transfer box or Gearbox?
Post by: MuddyMike on September 20, 2012, 11:25:10
If its coming from the front of the vehicle it could also be a CV joint. They make a tinkleing sound when on lock as they start to fail.

Mike
Title: Re: Transfer box or Gearbox?
Post by: Big G on September 20, 2012, 12:33:17
Thanks Mike. Is CV same as swivel?  How would I check for possible failure?
Title: Re: Transfer box or Gearbox?
Post by: lambert on September 20, 2012, 17:14:17
Cv is the gubbins inside the swivel. You can sometimes feel if the Cv is dying by rotating the wheel on full lock listening and feeling for notches clicking but not always. That said they are not that hard to strip down.
Title: Re: Transfer box or Gearbox?
Post by: Big G on September 20, 2012, 18:53:32

Right then chaps thats my plan of action sorted.

Tomorow afternoon get the Truck on my mates ramp and realy give the UJs a good examination and change any suspected of wear.

Inspect the swivel joints.Cvs for any signs of wear. strip down and inspect swivel joint gubbins when time available.

Very grateful for you guys taking the time and effort to post a reply. Will keep you updated.

G
Title: Re: Transfer box or Gearbox?
Post by: V8MoneyPit on September 20, 2012, 22:16:16
My money is on Mr Coverdale's UJ's.... well, not his UJ's. I don't know him that well  :shocked:
Title: Re: Transfer box or Gearbox?
Post by: Big G on September 28, 2012, 11:06:30
Just to update...

Had the truck up on the ramp and found play in the rear prop-shaft UJ`s. Went to my local guys (AMD) at Merrylees and got the GKN ones with nipples for eight pound a piece. Decided to do front as well while we were at it so got four new UJ`s. Pretty straight forward job except for the fine threaded bolts that come out of the transfer box front and rear. Got away with the rear ones but the threads on the front ones were shaggged so we replaced these.

Greased all the joints and splines and took it for a test run ........ sorted.

Just leaves me to say thank you to the boys who took the time and trouble to reply to my request for advice...... Lambert, Mike, and Mr Moneypit. Thank you.

G
Title: Re: Transfer box or Gearbox?
Post by: lambert on September 28, 2012, 14:50:38
Glad I we could help.
Title: Re: Transfer box or Gearbox?
Post by: Saffy on September 28, 2012, 19:49:10
Least now you  will recognise that sound next time ( in a few months  :grin: )
SimplePortal 2.3.5 © 2008-2012, SimplePortal