AuthorTopic: Disco 1 alloys  (Read 962 times)

0 Members and 1 Guest are viewing this topic.

Offline 300TDi Disco

  • Posts: 412
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Disco 1 alloys
« on: June 06, 2009, 20:32:29 »
Hi, would the disco 1 alloys fit on a defender 90 (hubs) ????


Cheers.
Let's Ave It.
One Life, Get One

Peugeot 206 XS
Fiat Ducato (work van)
Disco 300TDI


Offline crazymac

  • Posts: 1891
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Re: Disco 1 alloys
« Reply #1 on: June 06, 2009, 21:35:40 »
In short, NO!!

People do it, but to make then fit the grind part of the heads of the 6 bolts that hold the hub drive member on!
I HAVE THE BODY OF A GOD

shame its Budda!!

Offline 300TDi Disco

  • Posts: 412
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Re: Disco 1 alloys
« Reply #2 on: June 07, 2009, 01:44:55 »
Just that i was offered some but i wasnt sure about the fit. Cheers
Let's Ave It.
One Life, Get One

Peugeot 206 XS
Fiat Ducato (work van)
Disco 300TDI


Offline Bush Tucker Man

  • Posts: 9161
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Re: Disco 1 alloys
« Reply #3 on: June 07, 2009, 08:43:59 »
Why not?

Check the wheel bolts, if they have slots machined across the faces there's no reason why they shouldn't fit.


If the 90 is post (I think??) 92, & a has a disc-braked (factory fitted) rear axle, they should be compatible anyway
Richard A Thackeray 
Defender 110Td5 'Heritage Gone, but not forgotten
Jaguar XKR; X88 JLT, also 'gone, but not forgotten'

Yorkshire Born & Bred, and proud of it.

"You Can Allus Tell A Yorkshireman, But You Can't tell Him Owt!"

Offline Disco-andy

  • Posts: 310
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Re: Disco 1 alloys
« Reply #4 on: June 07, 2009, 19:07:25 »
If its a 300tdi defender or later they will go strait on, if its an early one you can put spacers on to get them to fit.
Other option is to put some disco axles on, if you don't already have disk brake at the back its supposed to be well worth it.

Offline Range Rover Blues

  • Moderator
  • ***
  • Posts: 15218
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +3/-0
    • South Yorkshire
  • Referrals: 0
Re: Disco 1 alloys
« Reply #5 on: June 07, 2009, 19:24:18 »
The hubs that were built to take alloys have studs with either a '-' or a triangle stamped on their outer ends.  I don't know what makes them different, whether it's their length or strength so I can't comment on whether it is safe to fit alloys to hubs not intended for them, but "I have been told" that if you remove the spring washers form the drive member securing boots that they do fit, however you will have the end of the halfshagft sticking out through the alloy.

If the halfshaft doesn't interfer with the alloy then either youhave non-LR alloys and I can offer no further advice or you have axles with alloy compatible hubs.

HOWEVER, only use alloys intended for the DEFENDER e.g. BOOST alloys if you have a 110 or 130, otherwise you are breaking the law, technically, as the other LR alloys are not weight-rated to carry the back axle of a longer Defender.
Blue,  1988  Range Rover 3.5 EFi with plenty of toys bolted on
Chuggaboom, 1995 Range Rover Classic
1995 Range Rover Classic Vogue LSE with 5 big sticks of Blackpool rock under the bonnet.

 






SimplePortal 2.3.5 © 2008-2012, SimplePortal