AuthorTopic: RR Classic Starting problems  (Read 2680 times)

0 Members and 1 Guest are viewing this topic.

Offline Agility eye

  • Posts: 10
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
RR Classic Starting problems
« on: May 25, 2006, 17:53:57 »
Hi Folks
Got an 87 RRC 3.5efi and it used to start with no problems even with a naff battery. it died eventualy
i put a new battery on and it seemed ok
i went to do an RTV trial with it and it was fine
The next day it took ages to start, it is firing but just wont keep going if you are persistant on the starter motor then you can get it going but runns Very lumpy if you get the revs up to 2000 for 20 seconds or so then its ok, but it could stall at any moment and you have to go through the whole procces again.
other thing i noticed is when it is starting up it smells very rich.
one last thing if i disconect the battery and leave it, come back reconect the battery it starts first time but still smells rich
Any ideas ???
Ian

Offline muddyman

  • Posts: 408
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
RR Classic Starting problems
« Reply #1 on: May 25, 2006, 23:49:55 »
Look at the air pipes from the air flow meter, they need to be in good nik, Try the ECU as well,  just my thoughts on it 8)

Offline Garth

  • Posts: 287
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
RR Classic Starting problems
« Reply #2 on: May 28, 2006, 00:00:20 »
Sounds like the electronic version of a choke is NG. What ever that is
Sorry cannot be more heplfull.
Does it do the same when its warm
"WINNE"
1991 VOUGE SE A WITH LPG
LOOKS GOOD (BUT LOOKS CAN BE DECEIVING)
"TIGGER"
1995 SUZUKI VITARA
1" LIFT
225/75X15 AT'S

Offline Garth

  • Posts: 287
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
RR Classic Starting problems
« Reply #3 on: May 28, 2006, 00:00:47 »
Sounds like the electronic version of a choke is NG. What ever that is
Sorry cannot be more heplfull.
Does it do the same when its warm
"WINNE"
1991 VOUGE SE A WITH LPG
LOOKS GOOD (BUT LOOKS CAN BE DECEIVING)
"TIGGER"
1995 SUZUKI VITARA
1" LIFT
225/75X15 AT'S

Offline muddyman

  • Posts: 408
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
RR Classic Starting problems
« Reply #4 on: May 28, 2006, 00:36:55 »
the cold start Injector sits on the left of the plenum chamber you can try it by takeing off the wires to it, they just pull off.

Offline FITZ4X4

  • Posts: 102
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
EFI strating rich
« Reply #5 on: May 30, 2006, 06:56:08 »
Most likly culprit and cheapest to replace is the Coolant Temperature sensor. Thses are prone to failure, they are easy to change and cost about £10.

If that fails to cure the problem it could be the Extra Air Valve or it's switch, the Thermotime Switch. These are the EFI's equivalent of a choke.

Heres some info you may find useful.

Extra Air Valve
The EAV allows extra air to bypass the throttle butterfly. This increase the engine RPM on idle when the engine is cold and prevents the engine stalling. When the fuel pump is running current is passed through a heating coil in the EAV. This heats a bi-metal leaf spring that slow closes the vavle until the engine is warm. Once the valve closes the heat in the now warm engine prevents the valve from opening until the engine stops and cools. On old engines this valve often sticks due to oil residues. It can often be clean sucessfully using carb cleaner.

Thermotime Switch
The thermo time switch controls the operation of the cold start injector. It is basically a pair of contact points, one of which is mounted on a bi-metal strip. A heater coil is fitted around the strip. The system works when the ignition switch is in the "crank" position. Whenever the bi-metal is cold the points are closed and the injector is operated. During the time the contacts are closed the current is heating up the strip. After max.12 secs (depending on ambient temperature) the bi-metal opens the points and injection stops. When the engine is already hot the bi-metal strip prevents the injector to operate during cranking. Notice that the extra air valve uses the same basic principle of a heated bi-metal strip.

Coolant Temperature Sensor
The Coolant Temperature sensor is located at the front of the inlet manifold in the coolant gallery.It can be mistaken for the thermotime switch as they are mounted side by side but the coolant tempreture sensor is less bulkier. It gives a signal to the ECU for engine temperature so that the ECU can inject more or less fuel depending on engine temperature. It does not affect the cold start injector!

Offline Agility eye

  • Posts: 10
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
RR Classic Starting problems
« Reply #6 on: May 30, 2006, 08:31:00 »
Thanks FITZ4X4 some good information their i will have a look at them.

Offline Range Rover Blues

  • Moderator
  • ***
  • Posts: 15218
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +3/-0
    • South Yorkshire
  • Referrals: 0
RR Classic Starting problems
« Reply #7 on: May 31, 2006, 02:49:51 »
Check your coil too, had that happen recently myself.
Blue,  1988  Range Rover 3.5 EFi with plenty of toys bolted on
Chuggaboom, 1995 Range Rover Classic
1995 Range Rover Classic Vogue LSE with 5 big sticks of Blackpool rock under the bonnet.

 






SimplePortal 2.3.5 © 2008-2012, SimplePortal